PC523 & PC526 – OCS ECU Replacement – 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima

“This site contains affiliate links for which OEMDTC may be compensated”

NHTSA Campaign Number: 16V911
Manufacturer Nissan North America, Inc.
Components AIR BAGS
Potential Number of Units Affected 757

 

Air Bag May Not Deploy Due to Software Issue

If the front passenger seat occupant is misclassified, the air bag may deploy incorrectly in the event of a crash, increasing the risk of injury.

 

Summary

Nissan North America, Inc. (Nissan) is recalling certain model year 2013-2015 Altima vehicles manufactured January 3, 2013, to July 29, 2013, 2015-2016 Rogue vehicles manufactured October 14, 2014, to August 12, 2016, and 2016 Maxima vehicles manufactured June 4, 2015, to August 19, 2015.

An incorrect Occupant Classification System (OCS) Electronic Control Unit (ECU) may have been installed in the front passenger seat.

The incorrect ECU and seat combination may misclassify the front passenger seat occupant.

 

Remedy

Nissan will notify owners, and dealers will replace the ECU and update the OCS software free of charge.

The is expected to begin by February 12, 2017.

Owners may contact Nissan customer service at 1-800-647-7261.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Nissan has a Recall

 

CAMPAIGN BULLETIN

OCS ECU Replacement Voluntary Safety Recall Campaign

 

Reference: PC523 & PC526
Date: December 20, 2016

 

Attention: Dealer Principal, Sales, Service & Parts Managers

IMPORTANT: It is a violation of Federal law for retailers to sell or deliver vehicles in their inventory covered by this notification until the campaign action is performed.

 

Affected Models/Years: Affected
Population:
Dealer
Inventory:
SERVICE COMM
Activation date:
Stop Sale In Effect
MY2016 Maxima (A36) 90 1 December 20th, 2016 YES
MY2013-15 Altima (L33) 483 NA
MY2015-16 Rogue (T32) 184 5

 

 

***** Campaign Summary *****

Nissan is committed to the safety and security of our customers and their passengers. Nissan has notified the National Highway Traffic Safety Administration (NHTSA) that it is conducting a Voluntary Safety Recall Campaign on a limited number of MY2013-15 Nissan Altima, MY2015-16 Nissan Rogue, and MY2016 Nissan Maxima vehicles to replace the Occupant Classification System (OCS) Electronic Control Unit (ECU) with a new unit.

Due to supplier labelling error that has since been corrected, an incorrect OCS ECU module may have been installed in the front passenger seat of some of the affected vehicles, resulting in the incorrect pairing of ECU-to-seat. With this configuration, the OCS may not perform as designed due to software incompatibility and may not classify a seated front passenger seat occupant correctly. This could cause the passenger airbag to not deploy as designed in a crash, increasing the risk of injury.

Owners of affected vehicles will be notified within sixty (60) days asking them to bring their vehicle to an authorized Nissan retailer to have their vehicle’s OCS ECU replaced.

 

***** What Dealers Should Do**** 

  1. Verify if vehicles are affected by these Voluntary Safety Recall Campaigns using the following Service Comm I.Ds:
    • PC523 – Altima and Maxima
    • PC526 – Rogue
      • New vehicles in dealer inventory can be also be identified using DCS (Sales-> Vehicle Inventory, and filter by Open Campaign).
        • Refer to NPSB 15-460 for additional information
Note: If a vehicle is affected by both R1609 and PC523 or PC526 and the R1609 remedy has not yet been performed, campaign PC523 or PC526 should be performed first.

 

  1. Dealers should not sell, lease, trade, rent or loan any vehicles in dealer inventory affected by this recall campaign until after the vehicle has been repaired.
  1. Dealers will use the procedure included with this announcement to replace the OCS control unit with the correct service part and reprogram with the latest OCS software.
  1. If a retailed vehicle affected by these campaign ID visits the dealer for service, the dealer should inform the customer about the recall campaign and communicate that parts may need to be ordered. Rental is covered under the campaign if parts need to be ordered.
EXPENSE CODE DESCRIPTION
502 Rental Expense $400 (Max)
Contact the Warranty claims call center 1-800-258-7008 Option 7, if additional expense is required.

 

***** Release Schedule ***** 

Parts
  • Parts for this campaign are currently restricted and may be ordered via the DCS ordering tool.
  • Pursuant to APRM policy 2.33.13, dealers are expected to comply with the parts return procedure. Dealers will be charged back for parts and labor found to be out of compliance with inspection and repair guidelines.
  • NOTE: Parts requested are VIN and repair order specific. It is important for dealers to return parts applicable to the VIN and repair order identified.
 

Repair

  • Campaign TSBs are currently under development and will be the subject of a future announcement
  • Please use the remedy procedure included with this announcement to remedy vehicles in dealer inventory as well as any affected retail vehicles
Owner Notification Nissan will begin notifying owners of all potentially affected vehicles within sixty

(60) days via U.S. Mail.

 

***** Dealer Responsibility ***** 

It is the dealer’s responsibility to check Service Comm using the appropriate Campaign I.D. for the campaign status on each vehicle falling within the range of this voluntary safety recall campaign which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in dealer inventory. If a VIN subject to this recall campaign was part of a dealer trade, the letter associated with that VIN should be forwarded to the appropriate dealer for service completion.

 

NISSAN NORTH AMERICA, INC.
Aftersales DIVISION

Frequently Asked Questions (FAQ):

 

Q. Is this a safety recall? 

A. Yes, a Stop Sale is in effect.

 

Q. What is the reason for safety recall? 

A. Due to supplier labelling error that has since been corrected, an incorrect OCS ECU module may have been installed in the front passenger seat of some of the affected vehicles, resulting in the incorrect pairing of ECU-to-seat.

 

Q. What is the possible effect of the condition?

A. With this configuration, the OCS may not perform as designed due to software incompatibility and may not classify a seated front passenger seat occupant correctly. This could cause the passenger airbag to not deploy as designed in a crash, increasing the risk of injury.

 

Q. What will be the corrective action for this voluntary safety recall campaign?

A. For affected vehicles, Nissan dealers will replace the Occupant Classification System (OCS) Electronic Control Unit (ECU) and reprogram it with the latest OCS software at no cost to you for parts and labor.

Note: If a vehicle is affected by both R1609 and PC523 or PC526 and the R1609 remedy has not yet been performed, campaign PC523 or PC526 should be performed first.

 

Q. How long will the corrective action take?

A. The remedy should take less than one (1) hour to complete. However, the Nissan dealer may require a longer period of time based upon their work schedule. All services will be provided at no cost to the customer for parts and labor.

 

Q. When will vehicle owners be notified?

A. Nissan will begin notifying owners of all potentially affected vehicles within sixty (60) days via U.S. Mail. Owners will be asked to bring their vehicle to an authorized Nissan dealer to have the Occupant Classification System (OCS) Electronic Control Unit (ECU) replaced and reprogrammed.

 

Q. Are parts readily available?

A. Parts are available via the DCS ordering tool under PC523 or PC526. Please refer to NPSB 16-526 for specific ordering instructions.

 

Q. Is my vehicle safe to drive?

A. Owners may drive the vehicle at their discretion. However, if the vehicle is subject to the recall, you should make arrangements to have your vehicle remedied as soon as possible.

 

Q. Will a rental vehicle be provided while the dealer is servicing the vehicle?

A. If parts are required, rental is covered by the campaign while parts are on order:

EXPENSE CODE DESCRIPTION
502 Rental Expense $400 (Max)
Contact the Warranty claims call center 1-800-258-7008 Option 7, if additional expense is required.

 

Q. I have lost confidence in the vehicle. Will Nissan replace or repurchase the vehicle?

A. The repair will fully correct this condition. As the condition will be corrected, there is no basis for repurchasing or replacing your vehicle.

 

Q. Is there anything owners can do to mitigate the condition?

A. No.

 

Q. Is there any charge for the repair?

A. No, the repair will be performed for the customer free of charge for parts and labor.

 

Q. Will I have to take my vehicle back to the selling dealer to have the service performed?

A. No, any authorized Nissan dealer is able to perform the recall campaign.

For Consumer Affairs: Please inform us of the dealer where you would like to have the corrective action completed.

 

Q. What model year vehicles are involved?

A. Certain MY2013-15 Nissan Altima, MY2015-16 Nissan Rogue, and MY2016 Nissan Maxima vehicles within a specific production range are affected.

 

Q. How many vehicles are involved in the campaign?

A. The North American Market is affected as follows:

 

Region Maxima Altima Rogue Total
USA 90 483 184 757
CANADA 5 9 0 14
Total 95 492 184 771

 

Make/Model Dates of Manufacture
MY2016 Nissan Maxima June 4, 2015 through August 19, 2016
MY2013-15 Nissan Altima January 3, 2013 through July 29, 2015
MY2015-16 Nissan Rogue October 14, 2014 through August 12, 2016

 

Q. Are you experiencing this condition on any other Nissan (or Infiniti) models?

A. No.

 

PC523 – ALTIMA (L33) – MAXIMA (A36)
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
REPLACEMENT AND REPROGRAMMING

 

CAMPAIGN INFORMATION

 

REQUIRED SPECIAL TOOL J-51594 (OCS Reprogramming Cable)

 J-51594 OCS reprogramming cable

 

  • One J-51594 OCS reprogramming cable has been supplied to each Additional cables can be obtained from Tech-Mate at 1-800-662-2001.

 

NOTE:

 

REPAIR OVERVIEW 

  1. Replace Occupant Classification System Control Unit
  1. Reprogram OCS control unit.
  1. Complete R1609 (NTB16-052b) IF still open in Service Comm.

 

 

SERVICE PROCEDURE 

  1. Turn the ignition ON, Engine OFF.
  1. Write down the radio settings.
Presets 1 2 3 4 5 6
AM
FM 1
FM 2
SAT 1
SAT 2
SAT 3

 

Bass Treble Balance Fade Speed Sen. Vol.

 

  1. If equipped, write down the customer preferred setting for the Automatic Air Conditioning System.
    • If needed, refer to System Settings in the HAC section of the Electronic Service Manual (ESM).
  1. Turn the vehicle OFF.
  1. Select the correct OCS control unit (OCS ECU) from Parts Information and confirm that the pin count is the same as the OCS control unit being replaced, See chart on Page 14.
  1. Replace the Occupant Classification System Control Unit (OCS ECU). Refer to the ESM section, SR – SRS Airbag for replacement of the Occupant Classification System Control Unit.
  1. Reset/reinitialize systems as needed.
    • Refer to the ESM section, PG – Power, Supply & Ground Elements for a listing of systems that require reset/initialization after reconnecting the 12V battery.
    • Look in the PG section index for ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL.
    • This list often includes items such as radio, power windows, clock, sunroof, etc.
  1. Proceed to next steps.

 

Preparing the Vehicle for Reprogramming

CAUTION:

  • Connect the GR8 to the 12V battery and select ECM Power Supply Mode. If the vehicle battery voltage goes below 0V or above 15.5V during reprogramming, the Occupant Classification System Control Unit (OCS ECU) may be damaged.
  • Be sure to turn OFF all vehicle electrical loads.
    If a vehicle electrical load remains ON, the OCS ECU may be damaged.
  • Be sure to connect the AC Adapter.
    If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the OCS ECU may be damaged.

 

  1. Make sure ASIST has been synchronized to the current date and all updates have been Installed. 

NOTE: The PC automatically gets applicable reprogramming software during ASIST synchronization.

  1. Open the vehicle hood, connect GR8 and set to ECM Power Supply Mode.
  1. Proceed to OCS Control Unit Reprogram steps on the next pages.

 

OCS Control Unit Reprogram 

NOTE: In this Service Procedure, OCS is sometimes referred to as ODS.

  1. Install the driver for the J-51594 OCS reprogramming cable as follows:
    1. Keep the PC connected to the internet.
    2. Connect the J-51594 OCS reprogramming cable to the PC USB port.
    3. Wait 1 minute, the drivers will install automatically.

NOTE: Step 1 above is only required the first time this procedure is performed. It is recommended that it be performed at the beginning of each day to confirm you have the latest software installed in your PC.

  1. Turn the ignition ON, engine OFF / not Ready and turn ON the hazard warning flasher lights (if not still ON).
  1. Connect the J-51594 OCS reprogramming cable:
  • Connect to the vehicle’s DLC connector and the PC USB port.
  • Make sure the cable is securely connected at both ends.
  1. Prepare the vehicle for OCS Reprogramming as follows:
  • Level the vehicle.
  • No objects on the passenger seat.
  • No occupants in the vehicle – including the servicing technician.
  • PC is outside of the vehicle on a suitable support.
    • Do not set the PC on the vehicle.
  • Do not touch the vehicle during the OCS Reprogramming.
  • Minimize vibrations of the vehicle.
  1. Open ASIST.
  1. Select “R1608 & R1609 OCS Reprogram” on ASIST under Specialty Tools (Figure 11).

ASISTFigure 11

 

NOTE: If you get a black message screen as shown in Figure 12, this indicates that the reprogramming cable is not connected, or the cable driver did not install correctly.

 

a. Close ODS Repro.

b. Close ASIST.

c. Start over from step 1 on page 5.

Black message screenFigure 12

 

  1. Select Start Repro.

NOTE: If the error message “an error occurred on connection” displays:

a. Disconnect the J-51594 OCS reprogramming cable, both ends.

b. Reconnect the cable; make sure it is securely connected at both ends.

Select Start ReproFigure 13

 

  1. Turn the ignition ON (engine OFF / not Ready).
  1. Select OK.
  • After selecting OK in Figure 14, the OCS reprogramming will start.

Select OKFigure 14

 

  • Items 1 through 4 (Figure 15) will likely complete quickly.
  • If the OCS reprogramming stops (displays NG) at item 1, 2, 3 or 4, refer to Figures 20 through 23 on pages 10 and 11.

OCS reprogramming will startFigure 15

 

  1. Cycle the ignition OFF > ON.
  1. Select OK.

Select OKFigure 16

 

  • After selecting OK in Figure 16, the OCS reprogramming will likely complete items 5 through 7 quickly (see “Complete” screen, Figure 18 below).
  • If the OCS reprogramming stops (displays NG) at item 5, 6 or 7, refer to Figures 24 through 26 on pages 12 and 13.

OCS reprogrammingFigure 17

 

  1. When this screen displays (Figure 18), OCS reprogramming is complete.
  1. Select OK.

OCS reprogramming is completeFigure 18

 

  1. Close the program (click on the red X in the upper right corner).
  1. Turn the ignition OFF.

Close the program (click on the red X in the upper right corner)Figure 19

 

  1. Disconnect the J-51594 OCS reprogramming cable.
  1. Disconnect the GR8, turn hazards OFF.
  1. Turn the ignition ON and observe the air bag warning light and the front passenger air bag status light:
    • The air bag warning light AirBag Light should illuminate for 7 seconds and then go out.
    • The front passenger airbag status light AirBag Light should illuminate for 7 seconds and then either stay illuminated or go out, depending on the occupation of the front passenger seat.

NOTE: If the air bag warning light or the front passenger airbag status light does not operate as described above, there may be an issue not covered by this campaign. Refer to ASIST and the appropriate ESM for additional diagnostic and repair information.

  1. OCS Reprogramming is Complete

NOTE:

  • Zero Point Reset was included in the reprogramming – it is not necessary to perform as a separate
  • Figures 20 through 26 on pages 10 through 13 are provided as reference if the OCS reprogramming stops (displays NG) at one of the items (1-7).
  1. Release the vehicle and submit a warranty claim using OP Code PC5230 (See Claim Information),

 

APPENDIX

  • #1 – If Connect indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Connect indicates NGFigure 20

 

  • #2 – If Read EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Connect indicates NGFigure 21

 

  • #3 – If Write EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Write EEPDATA indicates NGFigure 22

 

  • #4 – If Check EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Check EEPDATA indicates NGFigure 23

 

  • #5 – If Reconnect indicates NG:
  1. Click OK on the accompanying error message.
  1. Turn the ignition OFF.
  1. Close ODS Repro (click on the red X in the upper right corner).
  1. Restart from step 1 on page 5.

Reconnect indicates NGFigure 24

 

  • #6 – If Zero Reset indicates NG:

a. Click OK on the accompanying error message.

b. Cycle the ignition OFF > ON.

  • If needed, retry ignition OFF > ON 5 times.

c. If Zero Reset still indicates NG, close ODS Repro (click on the red X in the upper right corner), and restart from step 1 on page

Zero Reset indicates NGFigure 25

 

  • #7 – If Read EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Read EEPDATA indicates NGFigure 26

 

PART INFORMATION ALTIMA

MODEL YEAR AND DATE (MO/YR) DESCRIPTION PART # QUANTITY
Altima 05/12 – 01/14 OCS ECU

(16 pin connector)

98856-3TY0A 1
01/14 – 04/16 OCS ECU

(10 pin connector)

98856-9HN0A 1

 

 

MAXIMA 

MODEL YEAR AND DATE (MO/YR) DESCRIPTION PART # QUANTITY
Maxima 03/15 –CY OCS ECU

(16 pin connector)

98856-4RB0A 1

 

 

Confirm that the number of pins of the new part are the same as the original OCS Control Unit.

(See Figures below).

16 Pin Connector

10 Pin Connector

 

CLAIMS INFORMATION

 

Submit a Campaign (CM) line claim using the following claims coding: Work Order Line Type: “CM” Campaign

Campaign: PC523 

Claim Type: CM
PNC: PC523
Symptom: ZZ
Diagnosis: 99
Description: Op Codes Flat Rate Time
Replace OCS control unit and reprogram PC5230 0.8H

 

PC526 – ROGUE (T32)
OCCUPANT CLASSIFICATION SYSTEM CONTROL
UNIT REPLACEMENT AND REPROGRAMMING

 

CAMPAIGN INFORMATION

 

REQUIRED SPECIAL TOOL J-51594 (OCS Reprogramming Cable)

J-51594 OCS reprogramming cable

  • One J-51594 OCS reprogramming cable has been supplied to each Additional cables can be obtained from Tech-Mate at 1-800-662-2001.

 

NOTE: 

 

REPAIR OVERVIEW

  1. Replace Occupant Classification System Control Unit
  1. Reprogram OCS control unit.
  1. Complete R1609 (NTB16-052b) IF still open in Service Comm.

 

SERVICE PROCEDURE 

  1. Turn the ignition ON, engine OFF.
  1. Write down the radio settings.
Presets 1 2 3 4 5 6
AM
FM 1
FM 2
SAT 1
SAT 2
SAT 3

 

Bass Treble Balance Fade Speed Sen. Vol.

 

  1. If equipped, write down the customer preferred setting for the Automatic Air Conditioning System.
    • If needed, refer to System Settings in the HAC section of the Electronic Service Manual (ESM).
  2. Turn the vehicle OFF.
  1. Select the correct OCS control unit (OCS ECU) from Parts Information and confirm that the pin count is the same as the OCS control unit being replaced, See chart on Page 14.
  1. Replace the Occupant Classification System Control Unit (OCS ECU). Refer to the ESM section, SR – SRS Airbag for replacement of the Occupant Classification System Control Unit.
  1. Reset/reinitialize systems as needed.
    • Refer to the ESM section, PG – Power, Supply & Ground Elements for a listing of systems that require reset/initialization after reconnecting the 12V battery.
    • Look in the PG section index for ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL.
    • This list often includes items such as radio, power windows, clock, sunroof, etc.
  1. Proceed to next steps.

 

Preparing the Vehicle for Reprogramming

CAUTION:

  • Connect the GR8 to the 12V battery and select ECM Power Supply Mode. If the vehicle battery voltage goes below 0V or above 15.5V during reprogramming, the Occupant Classification System Control Unit (OCS ECU) may be damaged.
  • Be sure to turn OFF all vehicle electrical loads.
    If a vehicle electrical load remains ON, the OCS ECU may be damaged.
  • Be sure to connect the AC Adapter.
    If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the OCS ECU may be damaged.

 

  1. Make sure ASIST has been synchronized to the current date and all updates have been installed. 

NOTE: The PC automatically gets applicable reprogramming software during ASIST synchronization.

  1. Open the vehicle hood, connect GR8 and set to ECM Power Supply Mode.
  1. Proceed to OCS Control Unit Reprogram steps on the next pages.

 

OCS Control Unit Reprogram 

NOTE: In this Service Procedure, OCS is sometimes referred to as ODS.

  1. Install the driver for the J-51594 OCS reprogramming cable as follows:
    1. Keep the PC connected to the internet.
    2. Connect the J-51594 OCS reprogramming cable to the PC USB port.
    3. Wait 1 minute, the drivers will install automatically.

NOTE: Step 1 above is only required the first time this procedure is performed. It is recommended that it be performed at the beginning of each day to confirm you have the latest software installed in your PC.

  1. Turn the ignition ON, engine OFF / not Ready and turn ON the hazard warning flasher lights (if not still ON).
  1. Connect the J-51594 OCS reprogramming cable:
  • Connect to the vehicle’s DLC connector and the PC USB port.
  • Make sure the cable is securely connected at both ends.
  1. Prepare the vehicle for OCS Reprogramming as follows:
  • Level the vehicle.
  • No objects on the passenger
  • No occupants in the vehicle – including the servicing technician.
  • PC is outside of the vehicle on a suitable support.
    • Do not set the PC on the vehicle.
  • Do not touch the vehicle during the OCS Reprogramming.
  • Minimize vibrations of the vehicle.
  1. Open ASIST.
  1. Select “R1608 & R1609 OCS Reprogram” on ASIST under Specialty Tools (Figure 11).

ASISTFigure 11

 

NOTE: If you get a black message screen as shown in Figure 12, this indicates that the reprogramming cable is not connected, or the cable driver did not install correctly.

a. Close ODS Repro.

b. Close ASIST.

c. Start over from step 1 on page 5.

Black message screenFigure 12

 

  1. Select Start Repro.

NOTE: If the error message “an error occurred on connection” displays:

a. Disconnect the J-51594 OCS reprogramming cable, both ends.

b. Reconnect the cable; make sure it is securely connected at both ends.

Select Start ReproFigure 13

 

  1. Turn the ignition ON (engine OFF / not Ready).
  1. Select OK.
  • After selecting OK in Figure 14, the OCS reprogramming will start.

Select OKFigure 14

 

  • Items 1 through 4 (Figure 15) will likely complete quickly.
  • If the OCS reprogramming stops (displays NG) at item 1, 2, 3 or 4, refer to Figures 20 through 23 on pages 10 and 11.

OCS reprogramming will startFigure 15

 

  1. Cycle the ignition OFF > ON.
  1. Select OK.

Select OKFigure 16

 

  • After selecting OK in Figure 16, the OCS reprogramming will likely complete items 5 through 7 quickly (see “Complete” screen, Figure 18 below).
  • If the OCS reprogramming stops (displays NG) at item 5, 6 or 7, refer to Figures 24 through 26 on pages 12 and 13.

OCS reprogrammingFigure 17

 

  1. When this screen displays (Figure 18), OCS reprogramming is complete.
  1. Select OK.

OCS reprogramming is completeFigure 18

 

  1. Close the program (click on the red X in the upper right corner).
  1. Turn the ignition OFF.

Close the program (click on the red X in the upper right corner)Figure 19

 

  1. Disconnect the J-51594 OCS reprogramming cable.
  1. Disconnect the GR8, turn hazards OFF.
  1. Turn the ignition ON and observe the air bag warning light and the front passenger air bag status light:
    • The air bag warning light AirBag Light should illuminate for 7 seconds and then go out.
    • The front passenger airbag status light AirBag Light should illuminate for 7 seconds and then either stay illuminated or go out, depending on the occupation of the front passenger seat.

NOTE: If the air bag warning light or the front passenger airbag status light does not operate as described above, there may be an issue not covered by this campaign. Refer to ASIST and the appropriate ESM for additional diagnostic and repair information.

  1. OCS Reprogramming is Complete

NOTE:

  • Zero Point Reset was included in the reprogramming – it is not necessary to perform as a separate
  • Figures 20 through 26 on pages 10 through 13 are provided as reference if the OCS reprogramming stops (displays NG) at one of the items (1-7).
  1. Release the vehicle and submit a warranty claim using OP Code PC5230 (See Claim Information),

 

APPENDIX

  • #1 – If Connect indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Connect indicates NGFigure 20

 

  • #2 – If Read EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Connect indicates NGFigure 21

 

  • #3 – If Write EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Write EEPDATA indicates NGFigure 22

 

  • #4 – If Check EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Check EEPDATA indicates NGFigure 23

 

  • #5 – If Reconnect indicates NG:
  1. Click OK on the accompanying error message.
  1. Turn the ignition OFF.
  1. Close ODS Repro (click on the red X in the upper right corner).
  1. Restart from step 1 on page 5.

Reconnect indicates NGFigure 24

 

  • #6 – If Zero Reset indicates NG:

a. Click OK on the accompanying error message.

b. Cycle the ignition OFF > ON.

  • If needed, retry ignition OFF > ON 5 times.

c. If Zero Reset still indicates NG, close ODS Repro (click on the red X in the upper right corner), and restart from step 1 on page

Zero Reset indicates NGFigure 25

 

  • #7 – If Read EEPDATA indicates NG:

a. Click OK on the accompanying error message.

b. Turn the ignition OFF.

c. Close ODS Repro (click on the red X in the upper right corner).

d. Restart from step 1 on page 5.

Read EEPDATA indicates NGFigure 26

 

PART INFORMATION

To obtain the correct OCS control unit for the vehicle you are working on use the COMPLETE VIN number and FAST parts system or other electronic parts system to look up the applicable control unit.

 

Confirm that the number of pins of the new part are the same as the original OCS Control Unit.

(See Figures below).

16 Pin Connector

10 Pin Connector

 

CLAIMS INFORMATION 

Submit a Campaign (CM) line claim using the following claims coding: Work Order Line Type: “CM” Campaign

Campaign: PC526 

Claim Type: CM
PNC: PC526
Symptom: ZZ
Diagnosis: 99
Description: Op Codes Flat Rate Time
Replace OCS control unit and reprogram PC5260 0.8H

 

 

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.92 MB]

 


 

Reprogramming

J2534-1 Re/Programming

 


Tutorial for Purchasing NERS Software

Software updated April 26, 2019 to version # 04.03.00. It is recommended the latest version of NERS be installed before connecting to a vehicle.

This NERS software supports reprogrammable Engine and Transmission control units from 1999 to 2019 model year vehicles, and 2005 MY and later VIN writing into ECUs, when using a Nissan validated pass-through device. Click the Reprogramming Tab for additional information on reprogramming. This software only provides ECU reprogramming, blank programming and VIN writing capability. It does not provide diagnostic or key programming capability. For Engine and Transmission control unit reprogramming and VIN writing capability on 2020 MY & newer, please use CONSULT-III plus or CONSULT-III plus R2R software.

Vehicle reprogramming requires the use of the following:

  • Nissan validated J2534-1 device
  • Nissan ECU Reprogramming Software (NERS)
  • Personal computer running Windows XP (SP2 or later) or Windows 7 or 10 64Bit
  • Applicable reprogram file

 

Nissan tested and validated the below listed devices. Nissan does not recommend the use of any other J2534-1 device not listed here.

Manufacturer Models
Actia PassThru +XS
Autel MaxiFlash Elite (with firmware v3.01)
Bosch Mastertech VCI (SFP v5.11.9)
Dearborn Group VSI-2534
Drew Technologies/OPUS IVS CarDAQ Plus, CarDAQ M, Mongoose ISO/CAN
Hella Gutmann Solutions Mega Macs 42 SE (DT VCI), Mega Macs 66 (DT66)
Texa TEXA Navigator TXTs Series

Click the below link to purchase NERS diagnostic software.

Purchase NERS Software

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will no longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

 


When you purchase a J-2534 reprogramming file, you will get a zip file containing a data file (.dat, .pdx, .xcal, .7z), a .csv or .xml file and a Reprog_readme.pdf. Please review the readme file for information on where to place the files in your PC.

Please Note that J2534-1 supports reprogramming on 1999 MY and later vehicles.

 

How to find the proper J-2534 Reprogramming ECU file:

In order for you to locate the proper ECU file, you will need to look up the applicable Technical Services Bulletin(TSB) for your vehicle. Instructions in the TSB will pinpoint and advise you of the ECU part # to enter below.

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will not longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

Special Note: Nissan and Infiniti vehicle uses a high level of security when Re/programming or Configuration is performed to the vehicle ECUs. With the release of NERS software version 04.00.01 or greater, technicians will be required to login with their Nissan or Infiniti Techinfo website user ID and password to perform Re/programming and Configuration in NERS.
Login Instruction Guide

 


September 2013, Nissan and Infiniti began the phase in of “Blank” Service Parts ECUs and TCMs. Depending upon the model and model year, replacement modules come WITHOUT software. When a replacement module is installed in an applicable vehicle for any reason, it will need to be programmed.

When you purchase a J-2534 Blank programming file, you will get a zip file containing a data file (.dat, .pdx, .xcal, .7z), a .csv or .xml file and a Reprog_readme.pdf. Please review the readme file for information on where to place the files in your PC.

 

How to find the proper J-2534 Blank Programming ECU file:

  • Obtain the blank ECU part number when you purchase the replacement ECU. Nissan’s and Infiniti’s parts catalog provides both the blank ECU part number and the ROM-DATA ID part number (after programming part number) to be used. Enter this blank ECU part number in the field below.

or

  • Using C-III plus software, retrieve the blank ECU part number from the new ECU. Enter this blank ECU part number in the field below.

Please note: Take care after making your selection that the listed vehicle information matches the vehicle you are programming.

  • Special Note: NERS Version 03.08 or higher supports Blank RWD, 5 speed TCM programming.

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will not longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

Special Note: Nissan and Infiniti vehicle uses a high level of security when Re/programming or Configuration is performed to the vehicle ECUs. With the release of NERS software version 04.00.01 or greater, technicians will be required to login with their Nissan or Infiniti Techinfo website user ID and password to perform Re/programming and Configuration in NERS.
Login Instruction Guide

 

PC523 & PC526 - OCS ECU Replacement - 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima | small light Drew Tech CarDAQ-Plus 3 Diagnostic Code Reader and J2534 Programming Tool
PC523 & PC526 - OCS ECU Replacement - 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima | small light Drew Technologies (DRWCDPLUSKIT) CarDAQ-Plus J2534 Flash Reprogramming Kit
PC523 & PC526 - OCS ECU Replacement - 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima | small light Drew Tech Mongoose Pro ISO-CAN 2
PC523 & PC526 - OCS ECU Replacement - 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima | small light VSI J2534 ECU Reprogrammer & Diagnostic Adapter
PC523 & PC526 - OCS ECU Replacement - 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima | small light BOSCH Automotive Tools MTECH2 Mastertech II J2534
PC523 & PC526 - OCS ECU Replacement - 2013-2015 Nissan Altima, 2015-2016 Rogue, & 2016 Maxima | small light Autel MaxiFlash Elite VCI J2534 Pass-Thru

 

www.nissan-techinfo.com

 


 

Bestseller No. 1
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
  • ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
  • J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
  • TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
  • J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
  • FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Bestseller No. 2
VNCI J2534 for Nano Diagnostic Tools,Support J2534 for Automatic Switch Mode Fast Communication
  • Application:Support most all of J2534 compatible software, most all of for software, ECU reprogramming in J2534 mode with programming voltage, supply software for diagnosing J1979 compatible vehicles.
  • Material:VNCI (Vehicle network communication interface) is a device that works between diagnostic software and vehicle. It is compatible with J2534 Passthru and for .
  • Advantage:Support J2534 and for mode in one device, and has automatic switch mode, more speedup, faster communication and reprogramming.VNCI J2534 for Nano protocol configuration include, for ISO15765, for ISO9141, for ISO14230, for J1850 PWM( supports IFR and 2X speed modes), for J1850 VPW (supports 4x speed mode).
  • Easy to install:More stability, never let you down while reprogramming, portable and convenient, small package and easy to carry.
  • Best Experience :We strive to provide you with the best quality products and the best customer experience.We try our best to meet your requirements.Please check the product information carefuly berore buying to aviod making mistakes.
Bestseller No. 3
LAUNCH X431 PRO5 Elite,J2534 Reprogramming Tool, Topology Mapping OBD2 Scanner Diagnostic Tool, CAN/CAFD/DoIP/HD/FCA SGW,Bidirectional Scan Tool, ECU Coding, 50+ Reset, All Systems Scanner
  • 🆚LAUNCH X431 PRO5 scan tool Upgrade all functions of X431 PRO3/X-431 Throttle III/X431-TorqueIII/X431 V+, PROS V+, PAD3. ⓵ J2534 ECU Programming &Online functions directly connect to OEM server, 50+ reset same as X-431 Throttle;⓶Bi-directional control and All system diagnostics as Snap-on scanner; ⓷ Support 150+ brands Vehicles (include CAN/CAFD/DoIP/HD protocols and AutoAuth for FCA SGW) ⓸Powered by 8-core processor(1.8GHz), Android9.0 OS, 2.4 & 5GHz WiFi connection.
  • 🚜[J2534 Reprogramming With FREE SMARTBOX 3.0】Save more than $2000, LAUNCH X431 PRO5 support J2534/DOIP/CANFD/HD protocols (Needn’t buy HDIII Module,Manufacture software and non-16pin adaptors need to be purchased separately.) Download OEM software from the manufacturer’s server to 1) program data to blank/used ECUs; 2) Reflash ECUs with data loss; 3)Upgrade ECU software version. As a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
  • 👏[50+ Reset, Continuously Updated Reset Functions]: With the LAUNCH diagnostic tool, You will never be bothered by tricky vehicle issues and keep pace with newer technology. 50 commonly reset functions ( in the quick page ) reaching into the smallest parts to root out the problems. Extra 300+ repair functions ( in-vehicle catalog) for specific models extend the capability to reset, regeneration, initiation, matching, etc. (Functions vary by models, configurations, and systems.)
  • 🌐[One stop Intelligent Diagnostic Tool]: LAUNCH X431 PRO5 obd2 scanner Bluetooth provides Repair Tips, Repair Assist, Component Measurement, TSB, Relevant Cases DTC Analysis to simplify complex diagnostic and achieve the trouble-free repair. 🤩[One Scanner For Multiple Uses]: LAUNCH diagnostic tool PRO5 collaborates with add-on modules (ADAS, Videoscope, TSGUN, X-ProG3, WiFi Pinter, Battery Tester) to expand business applications and improve diagnostic accuracy.
  • 👍【2024 New OE Level Online Functions 】Bidirectional Scan Tool offers you various high-end online functions, which enable you to access the online data to do fast & complicated vehicle repairs, e.g. 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for BMW, Audi, VW, Porsche, Benz to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
Bestseller No. 4
Mongoose-Plus J2534 OEM Vehicle Interface Cable - GM OEM Reprogramming and Diagnostics
  • Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, Subaru, & VW/Audi.
  • Supports Current GM Vehicles: Now includes CAN-FD, DoIP (Diagnostics over Internet Protocol - as defined in J2534-2) and support for J2534 version 5.0. This is the tool that GM dealerships use for diagnostics and reprogramming.
  • NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
  • Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
  • Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
Bestseller No. 5
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Multi-Protocol PassThru Interface, Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MS908CV, MK908P, MK908 Pro II and PC
  • 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
  • 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
  • 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
  • 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
Bestseller No. 6
VXDIAG VCX Nano GDS2 and Tech2Win Diagnostic Tool Compatible for GM/OPEL with Global Diagnostic Programming System GDS & GDS2 Blue
  • 🚗[Technical assistance] If you have any installation problems, download the installation manual. Or please contact us at any time. We can provide technical support and help you install software online
  • 🚗[Vehicle Coverage] Installation Tips: Please turn off anti-virus software before install. VXDIAG VCX NANO fully compatible with SAE-J2534-1 & SAE-J2534-2. All current and most legacy vehicle protocols: CAN, UART, KW2000, Class2, GM LAN, etc.
  • 🚗[Functional] ●USB vehicle-to-PC connectivity●Supports Windows,XP●CE and FCC compliance for hardware●Firmware Updatable. 【SPS】Service Programming System: ◎Passthrough programming on GM past model and Global A vehicles◎Increase reprogramming speed 20-70% and get ready to service new models.
  • 🚗[GDS] Global Diagnostic System: ◎New Diagnostic Application Software required for all GM Global Architecture (Global A) Vehicles. ◎GDS & GDS2 is software which runs on a specific PC. Updates received via TIS2Web.
  • 🚗[Efficient&Convenience] Quick access to vehicle data for maintenance or management reports.Quickly attaches to vehicle's diagnostic connector. Mixed fleet capabilities with broad protocol support.May be used with desktop PC or laptop. make sure your computer at least 4GB.Tech2win software only installed on 7 32bit computer and on physical system.Please download the latest vxmanager from vxdiag official website.

Last update on 2024-03-18 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


 

Leave a Comment

Share to...