2023-2024 Nissan Kicks, Sentra & Versa; Driver Air Bag Module

SEOCONTENT-START

Classification: Reference: Date:
RS24-005 NTB24-020 February 28, 2024
Bulletins are intended for use by qualified technicians, not ‘do-it-yourselfers’. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/7
VOLUNTARY SAFETY RECALL CAMPAIGN
2023-2024 KICKS, SENTRA AND VERSA;
DRIVER AIR BAG MODULE
CAMPAIGN ID #: PMA34
APPLIED VEHICLES: 2023-2024 Kicks (P15)
2023-2024 Sentra (B18)
2023-2024 Versa (N18)
Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.
INTRODUCTION
Nissan is conducting this voluntary safety recall campaign on certain specific model year
2023-2024 Kicks, Sentra, and Versa vehicles to replace the driver air bag module. This
service will be performed at no charge to the customer for parts or labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number PMA34 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS)
National Service History for the campaign status on each vehicle falling within the range of
this voluntary safety recall which for any reason enters the service department. This
includes vehicles purchased from private parties or presented by transient (tourist) owners
and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer
inventory which are the subject of a safety recall must be corrected prior to sale.
Failure to do so can result in civil penalties by the National Highway Traffic Safety
Administration. While federal law applies only to new vehicles, Nissan strongly
encourages dealers to correct any used vehicles in their inventory before they are retailed.
2/7 NTB24-020
REQUIRED SPECIAL TOOL(S)
New or replacement Essential Tools are available from Tech Mate online:
www.techmatetools.com, or by phone: 1-833-397-3493.
When ordering, keep in mind that the tool part number prefix has changed from “J” to “NI”.
For example, J-52352 is now NI-52352.
Quick Scan Tool (NI-52352)
 Each dealer has been previously shipped one Quick Scan Tool (NI-52352).
Figure 1
3/7 NTB24-020
SERVICE PROCEDURE
To avoid the risk of death or severe personal injury, follow all cautions, warnings, and notes
in the ESM when working on or near a Supplemental Restraint System (SRS), such as an
air bag.
To avoid damage to the vehicle, handle interior trim carefully. Work with clean hands
and clean tools to avoid dirt and stains. Use protective covers as needed.
HINT: Some radios will lose presets when disconnecting the battery. Using the table below
should be considered. Refer to the ESM: ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL.
Presets 1 2 3 4 5 6
AM
FM 1
FM 2
SAT 1
SAT 2
Bass Treble Balance Fade Speed Sen.
Vol.
1. Turn the ignition OFF.
2. Disconnect both battery cables, battery negative cable first.
3. Wait at least 3 minutes.
4/7 NTB24-020
New Driver Air Bag Module Registration
4. Obtain a new driver air bag module from your parts department.
 The new driver air bag module is listed in the PARTS INFORMATION.
Figure 2
6. On the left side of ASIST main menu, select TECH SUPPORT INFO, and then
Inventory Vehicle Actions.
Figure 3
5. Attach the Quick Scan Tool (NI-52352)
to your CONSULT PC USB port.
TECH SUPPORT
INFO
Inventory Vehicle Actions
5/7 NTB24-020
7. Select CLICK HERE (Airbag to VIN Registration).
Figure 4
Figure 5
Select CLICK HERE
9. Use the Quick Scan Tool to scan the
bar code (VIN) on the B-pillar label.
 Wipe any dirt/debris from bar code
before scanning.
HINT:
 Some labels may not scan quickly.
 Hold the scan tool approximately
6 inches away from the label.
 Hold the trigger down until the
label is read (this may take several
seconds).
6/7 NTB24-020
 The VIN will automatically populate (Figure 6).
 If needed, the VIN can be entered manually.
Figure 6
Figure 7
11. Select Submit on the ASIST screen.
Step 11
(Select Submit after both
fields are populated).
10. Use the Quick Scan Tool to scan
the bar code (serial number) on the
new driver air bag module.
 The serial number will
automatically populate.
HINT: If needed, the serial number
can be entered manually.
Bar code
Serial number
xxxx
xxxx
xxxxxxxxxxxxxx
7/7 NTB24-020
12. Remove and replace the driver air bag module.
 Refer to the ESM: RESTRAINTS > SRS AIR BAG > REMOVAL AND
INSTALLATION > DRIVER AIR BAG
13. Reconnect both battery cables, battery negative cable last.
 Nut torque: 8.0 N•m (0.82 kg-m, 71 in-lb)
14. Reset the clock and the radio settings.
15. Perform required additional service.
 Refer to the ESM: ELECTRICAL & POWER CONTROL > POWER SUPPLY,
GROUND & CIRCUIT ELEMENTS > BASIC INSPECTION > INSPECTION AND
ADJUSTMENT > ADDITIONAL SERVICE WHEN REMOVING BATTERY
NEGATIVE TERMINAL > Required Procedure After Battery Disconnection
PARTS INFORMATION
DESCRIPTION PART NUMBER QUANTITY
MODULE ASSY-AIR BAG 98510-xxxxx (1) 1
(1) Use the EPC and the VIN of the vehicle you are working on to obtain the correct part
number
CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID DESCRIPTION OP CODE FRT
PMA34
Replace Driver’s Air Bag Module (Kicks) PMA340 0.5
Replace Driver’s Air Bag Module
(Sentra And Versa) PMA341 0.6
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE DESCRIPTION
February 28, 2024 NTB24-020 Original bulletin published

**************************************************************************************************************

**************************************************************************************************************

SEOCONTENT-END