NTB22-083 – TCM Reprogram – 2023 Nissan Z

“This site contains affiliate links for which OEMDTC may be compensated”
Classification:

AT22-013

Reference:

NTB22-083

Date:

September 23, 2022

 

VOLUNTARY SAFETY RECALL CAMPAIGN
2023 Z; TCM REPROGRAM

CAMPAIGN ID #: R22B2

APPLIED VEHICLES: 2023 Z (Z34)

 

INTRODUCTION 

Nissan is conducting this voluntary safety recall campaign on certain specific model year 2023 Z vehicles to inspect and, if necessary, reprogram the Transmission Control Module (TCM). This service will be performed at no charge to the customer for parts or labor.

 

IDENTIFICATION NUMBER 

Nissan has assigned identification number R22B2 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign.

 

REPAIR OVERVIEW

Confirm the current TCM part number.

Reprogram the TCM, if applicable.

This bulletin is complete.

 


SERVICE PROCEDURE 

IMPORTANT: Before starting, make sure:

ASIST on the CONSULT PC has been synchronized (updated) to the current date. All C-III plus software updates (if any) have been installed.

 

NOTICE

  • Connect a battery maintainer or smart charger set to reflash mode or a similar setting. If the vehicle battery voltage drops below 0V or rises above 15.5V during reprogramming, the TCM may be damaged.
  • Turn the hazard warning lamps ON.
    • Turn OFF all other vehicle electrical loads such as exterior lights, interior lights, HVAC, blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc. If a vehicle electrical load remains ON, the TCM may be damaged.
  • Be sure to connect the AC If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the TCM may be damaged.
  • Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the If Bluetooth® signal waves are within range of the CONSULT PC or VI during reprogramming, reprogramming may be interrupted and the TCM may be damaged.

 

  1. Connect a battery maintainer/smart charger to the vehicle.

 

  1. Connect the VI to the vehicle.

 

  1. Start C-III plus.

 

  1. Wait for the VI to be recognized.
    • The serial number will display when the VI is

 

  1. Select Re/programming, Configuration.

 

  1. Check the box to confirm the precaution instructions have been read, and then select Next.

NOTE: Use the arrows (if needed) to view and read all the precautions.

 

  1. Select Automatic Selection(VIN).

 

  1. Allow C-III plus to perform automatic VIN selection.

 

  1. Confirm the VIN or Chassis # is correct, and then select Confirm.

 

  1. Allow the System call to be performed.

 

  1. Confirm the VIN is correct for the vehicle, and then select Confirm.

 

  1. Select TRANSMISSION.

 

  1. Select Reprogramming.

 

  1. Find the TCM Part Number and write it on the repair order, and then select Save.

NOTE: This is the current Part Number (P/N).

 

  1. Compare the Part Number you wrote down in step 14 on page 8 to the numbers in the Current TCM Part Number column in Table A below.
  • If there is a match, proceed to step 16, below, to continue the reprogramming procedure.
  • If there is not a match, this bulletin does not Proceed to CLAIMS INFORMATION on the last page.

 

Table A

MODEL CURRENT TCM PART NUMBER: 31039 –
2023 Z 6GP2A

 

Reprogram the TCM 

  1. Follow the on-screen instructions to navigate C-III plus and reprogram the TCM.
  • If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle.

 

  1. Select Next, and then proceed to step 18 on page 12.

NOTE: When the screen in Figure 12 displays, TCM reprogramming is complete. If the screen in Figure 12 does not display (indicating that reprogramming did not complete), refer to the information on the next page.

 

TCM Recovery:

Do not disconnect the VI or shut down C-III plus if reprogramming does not complete. 

If reprogramming does not complete and the “!?” icon displays, as shown in Figure 13:

  • Check battery voltage (12.0 V – 15.5 V).
  • Ignition is ON, engine is OFF.
  • External Bluetooth® devices are OFF.
  • All electrical loads are OFF.
  • Select retry and follow the on screen instructions.
  • “Retry” may not go through on first attempt and can be selected more than once.

 

If reprogramming does not complete and the “X” icon displays, as shown in Figure 14: 

  • Check battery voltage (12.0 V – 15.5 V).
  • CONSULT A/C adapter is plugged in.
  • Ignition is ON, engine is OFF.
  • All C-III plus / VI cables are securely connected.
  • All C-III plus updates are installed.
  • Select Home, and restart the reprogram procedure from the beginning.

 

  1. Follow the on-screen instructions to Erase All DTCs.
    • When the entire reprogramming process is complete, the screen in Figure 15 will display.

 

  1. Verify the before and after part numbers are different.

 

  1. Print a copy of this screen (Figure 15) and attach it to the repair order for warranty documentation.

 

  1. Select Confirm.

 


Transmission Control Module (TCM) Reprogram – 2020-2023 Nissan Titan & Frontier

 

Transmission Control Module (TCM) Reprogram – 2020-2023 Nissan Titan & Frontier

 


Remedy Instructions and TSB

RCRIT-22V671-1964.pdf 4409.116KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [4.20 MB]

 


Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V671&docType=RCL

 


 

Reprogramming

J2534-1 Re/Programming

 


Tutorial for Purchasing NERS Software

Software updated April 26, 2019 to version # 04.03.00. It is recommended the latest version of NERS be installed before connecting to a vehicle.

This NERS software supports reprogrammable Engine and Transmission control units from 1999 to 2019 model year vehicles, and 2005 MY and later VIN writing into ECUs, when using a Nissan validated pass-through device. Click the Reprogramming Tab for additional information on reprogramming. This software only provides ECU reprogramming, blank programming and VIN writing capability. It does not provide diagnostic or key programming capability. For Engine and Transmission control unit reprogramming and VIN writing capability on 2020 MY & newer, please use CONSULT-III plus or CONSULT-III plus R2R software.

Vehicle reprogramming requires the use of the following:

  • Nissan validated J2534-1 device
  • Nissan ECU Reprogramming Software (NERS)
  • Personal computer running Windows XP (SP2 or later) or Windows 7 or 10 64Bit
  • Applicable reprogram file

 

Nissan tested and validated the below listed devices. Nissan does not recommend the use of any other J2534-1 device not listed here.

Manufacturer Models
Actia PassThru +XS
Autel MaxiFlash Elite (with firmware v3.01)
Bosch Mastertech VCI (SFP v5.11.9)
Dearborn Group VSI-2534
Drew Technologies/OPUS IVS CarDAQ Plus, CarDAQ M, Mongoose ISO/CAN
Hella Gutmann Solutions Mega Macs 42 SE (DT VCI), Mega Macs 66 (DT66)
Texa TEXA Navigator TXTs Series

Click the below link to purchase NERS diagnostic software.

Purchase NERS Software

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will no longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

 


When you purchase a J-2534 reprogramming file, you will get a zip file containing a data file (.dat, .pdx, .xcal, .7z), a .csv or .xml file and a Reprog_readme.pdf. Please review the readme file for information on where to place the files in your PC.

Please Note that J2534-1 supports reprogramming on 1999 MY and later vehicles.

 

How to find the proper J-2534 Reprogramming ECU file:

In order for you to locate the proper ECU file, you will need to look up the applicable Technical Services Bulletin(TSB) for your vehicle. Instructions in the TSB will pinpoint and advise you of the ECU part # to enter below.

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will not longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

Special Note: Nissan and Infiniti vehicle uses a high level of security when Re/programming or Configuration is performed to the vehicle ECUs. With the release of NERS software version 04.00.01 or greater, technicians will be required to login with their Nissan or Infiniti Techinfo website user ID and password to perform Re/programming and Configuration in NERS.
Login Instruction Guide

 


September 2013, Nissan and Infiniti began the phase in of “Blank” Service Parts ECUs and TCMs. Depending upon the model and model year, replacement modules come WITHOUT software. When a replacement module is installed in an applicable vehicle for any reason, it will need to be programmed.

When you purchase a J-2534 Blank programming file, you will get a zip file containing a data file (.dat, .pdx, .xcal, .7z), a .csv or .xml file and a Reprog_readme.pdf. Please review the readme file for information on where to place the files in your PC.

 

How to find the proper J-2534 Blank Programming ECU file:

  • Obtain the blank ECU part number when you purchase the replacement ECU. Nissan’s and Infiniti’s parts catalog provides both the blank ECU part number and the ROM-DATA ID part number (after programming part number) to be used. Enter this blank ECU part number in the field below.

or

  • Using C-III plus software, retrieve the blank ECU part number from the new ECU. Enter this blank ECU part number in the field below.

Please note: Take care after making your selection that the listed vehicle information matches the vehicle you are programming.

  • Special Note: NERS Version 03.08 or higher supports Blank RWD, 5 speed TCM programming.

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will not longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

Special Note: Nissan and Infiniti vehicle uses a high level of security when Re/programming or Configuration is performed to the vehicle ECUs. With the release of NERS software version 04.00.01 or greater, technicians will be required to login with their Nissan or Infiniti Techinfo website user ID and password to perform Re/programming and Configuration in NERS.
Login Instruction Guide

 

NTB22-083 - TCM Reprogram - 2023 Nissan Z | small light Drew Tech CarDAQ-Plus 3 Diagnostic Code Reader and J2534 Programming Tool
NTB22-083 - TCM Reprogram - 2023 Nissan Z | small light Drew Technologies (DRWCDPLUSKIT) CarDAQ-Plus J2534 Flash Reprogramming Kit
NTB22-083 - TCM Reprogram - 2023 Nissan Z | small light Drew Tech Mongoose Pro ISO-CAN 2
NTB22-083 - TCM Reprogram - 2023 Nissan Z | small light VSI J2534 ECU Reprogrammer & Diagnostic Adapter
NTB22-083 - TCM Reprogram - 2023 Nissan Z | small light BOSCH Automotive Tools MTECH2 Mastertech II J2534
NTB22-083 - TCM Reprogram - 2023 Nissan Z | small light Autel MaxiFlash Elite VCI J2534 Pass-Thru

 

www.nissan-techinfo.com

 


 

Bestseller No. 1
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
  • ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
  • J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
  • TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
  • J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
  • FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Bestseller No. 2
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Vehicle Communication Interface,Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MK908 Pro II, MS908CV, MK908P and PC
  • 【As a multi-protocol Pass-Thru vehicle interface】MaxiFlash Elite is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device. Specially designed to provide users with convenient PC communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, MaxiFlash Elite offers the most significant features desired by OEM customers: reliability, fast performance and flexibility.
  • 【MaxiFlash Elite is an accessory tool for MK908P, MS908S Pro】Autel MaxiSys Elite to program ECUs on specific for BMW and for Benz vehicles, in case you lost the J-2534 programmer. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your tablet MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. The functions are NOT universally compatible. Please send VIN number to 🚘jmxd2022@outlook.com📧🚘 to check compatibility before your order. If need any supports, Please contact us.
  • 【Wireless with advanced networking functions】Built-In Wireless with advanced networking functions and data storage. Fast performance ensures reprogramming even the newest controllers & Internet upgradable and updatable. Autel MaxiFlash Elite is compatiable with MaxiSYS MS908S, MaxiSYS MS908S Pro , MaxiSYS MS908CV, MaxiCOM MK908, MaxiCOM MK908 Pro, MaxiSYS Elite, MaxiSYS Elite II and Personal Computer
  • 【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 【Supports simultaneous communication Definition in J2534-1】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed.Rugged aluminum case with non-slip rubber end caps, capable of withstanding harsh environment.
Bestseller No. 3
Mongoose-Plus J2534 OEM Vehicle Interface Cable - Ford/Lincoln/Mercury OEM Reprogramming and Diagnostics
  • Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, & VW/Audi.
  • Supports Current & Earlier Vehicles: Enables diagnostics, programming and other “dealer” functions through OEM applications
  • NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
  • Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
  • Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
Bestseller No. 4
Latest Version ECUs Programmer SM2Pro J2534VCI Read Write 67IN1 Dongle Suiatble for Efficient ECUs Programming Durable Diagnostic Tool Plastic ECUs Programmer Vehicle Repair Tool Engine Diagnostic
  • Stay up-to-date with thelatest firmware and support of the SM2Pro J2534VCI ECUs programmer, ensuring reliable perform and optimalresults.
  • The SM2Pro J2534VCI ECUs programmer is a trustedtool for professional technicians, offering comprehensive functionality and easy integration into your workflows.
  • The SM2Pro J2534VCI ECUs programmer offersadvanced functionality for efficient and precise ECUs programming.
  • With its 67IN1 without dongle & OBDcompatibility, the SM2Pro J2534VCI ECUs programmer provides a versatilesolution for read and write operations.
  • Experienceseamless ECUs programming with the SM2Pro J2534VCI, designed to streamlines the read and write processes for enhanced efficiency.
Bestseller No. 5
OBDLink EX FORScan OBD Adapter
  • CUSTOM-DESIGNED FOR USE WITH FORSCAN and recommended by the FORScan Team
  • DEALERSHIP-LEVEL DIAGNOSTICS: OBDLink EX supports all Ford protocols, modules, and advanced features of FORScan
  • ELECTRONIC SWITCH allows FORScan to access all CAN buses simultaneously and enables advanced functions not possible with “toggle switch” adapters
  • MAXIMUM THROUGHPUT -- up to 20 times faster than “toggle switch” adapters
  • ROCK-SOLID CONNECTION avoids data corruption and dropped packets
Bestseller No. 6
VXDIAG VCX Nano GDS2 and Tech2Win Diagnostic Tool Compatible for GM/OPEL with Global Diagnostic Programming System GDS & GDS2 Blue
  • 🚗[Technical assistance] If you have any installation problems, download the installation manual. Or please contact us at any time. We can provide technical support and help you install software online
  • 🚗[Vehicle Coverage] Installation Tips: Please turn off anti-virus software before install. VXDIAG VCX NANO fully compatible with SAE-J2534-1 & SAE-J2534-2. All current and most legacy vehicle protocols: CAN, UART, KW2000, Class2, GM LAN, etc.
  • 🚗[Functional] ●USB vehicle-to-PC connectivity●Supports Windows,XP●Supports Windows 7● CE and FCC compliance for hardware●Firmware Updatable. 【SPS】Service Programming System: ◎Passthrough programming on GM past model and Global A vehicles◎Increase reprogramming speed 20-70% and get ready to service new models.
  • 🚗[GDS] Global Diagnostic System: ◎New Diagnostic Application Software required for all GM Global Architecture (Global A) Vehicles. ◎GDS & GDS2 is software which runs on a specific PC. Updates received via TIS2Web.
  • 🚗[Efficient&Convenience] Quick access to vehicle data for maintenance or management reports.Quickly attaches to vehicle's diagnostic connector. Mixed fleet capabilities with broad protocol support.May be used with desktop PC or laptop. make sure your computer at least 4GB.Tech2win software only installed on 7 32bit computer and on physical system.Please download the latest vxmanager from vxdiag official website.

Last update on 2024-05-17 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...