2023 Nissan Rogue, 2024 Frontier, 2024 Pathfinder, & 2024 Titan; Driver Air Bag Module

SEOCONTENT-START

Classification: Reference: Date:
RS24-002 NTB24-019 February 28, 2024
Bulletins are intended for use by qualified technicians, not ‘do-it-yourselfers’. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/7
VOLUNTARY SAFETY RECALL CAMPAIGN
2023 ROGUE, 2024 FRONTIER, 2024 PATHFINDER,
AND 2024 TITAN; DRIVER AIR BAG MODULE
CAMPAIGN ID #: PD103
APPLIED VEHICLES: 2023 Rogue (T33)
2024 Frontier (D41)
2024 Pathfinder (R53)
2024 Titan (A61)
Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.
INTRODUCTION
Nissan is conducting this voluntary safety recall campaign on certain specific model year
2023 Rogue, 2024 Frontier, 2024 Pathfinder, and 2024 Titan vehicles to replace the driver
air bag module. This service will be performed at no charge to the customer for parts or
labor.
IDENTIFICATION NUMBER
Nissan has assigned identification number PD103 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.
DEALER RESPONSIBILITY
It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS)
National Service History for the campaign status on each vehicle falling within the range of
this voluntary safety recall which for any reason enters the service department. This
includes vehicles purchased from private parties or presented by transient (tourist) owners
and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer
inventory which are the subject of a safety recall must be corrected prior to sale.
Failure to do so can result in civil penalties by the National Highway Traffic Safety
Administration. While federal law applies only to new vehicles, Nissan strongly
encourages dealers to correct any used vehicles in their inventory before they are retailed.
2/7 NTB24-019
REQUIRED SPECIAL TOOL(S)
New or replacement Essential Tools are available from Tech Mate online:
www.techmatetools.com, or by phone: 1-833-397-3493.
When ordering, keep in mind that the tool part number prefix has changed from “J” to “NI”.
For example, J-52352 is now NI-52352.
Quick Scan Tool (NI-52352)
 Each dealer has been previously shipped one Quick Scan Tool (NI-52352).
Figure 1
3/7 NTB24-019
SERVICE PROCEDURE
To avoid the risk of death or severe personal injury, follow all cautions, warnings, and notes
in the ESM when working on or near a Supplemental Restraint System (SRS), such as an
air bag.
To avoid damage to the vehicle, handle interior trim carefully. Work with clean hands
and clean tools to avoid dirt and stains. Use protective covers as needed.
1. Turn the ignition OFF.
2. Disconnect both battery cables, battery negative cable first.
3. Wait at least 3 minutes.
New Driver Air Bag Module Registration
4. Obtain a new driver air bag module from your parts department.
 The new driver air bag module is listed in the PARTS INFORMATION.
Figure 2
5. Attach the Quick Scan Tool (NI-52352)
to your CONSULT PC USB port.
4/7 NTB24-019
6. On the left side of ASIST main menu, select TECH SUPPORT INFO, and then
Inventory Vehicle Actions.
Figure 3
7. Select CLICK HERE (Airbag to VIN Registration).
Figure 4
TECH SUPPORT
INFO
Inventory Vehicle Actions
Select CLICK HERE
5/7 NTB24-019
Figure 5
 The VIN will automatically populate (Figure 6).
 If needed, the VIN can be entered manually.
Figure 6
9. Use the Quick Scan Tool to scan the
bar code (VIN) on the B-pillar label.
 Wipe any dirt/debris from bar code
before scanning.
HINT:
 Some labels may not scan quickly.
 Hold the scan tool approximately
6 inches away from the label.
 Hold the trigger down until the
label is read (this may take several
seconds).
Step 11
(Select Submit after both
fields are populated).
xxxx
xxxx
6/7 NTB24-019
Figure 7
11. Select Submit on the ASIST screen.
12. Remove and replace the driver air bag module.
 Refer to the ESM: RESTRAINTS > SRS AIR BAG > REMOVAL AND
INSTALLATION > DRIVER AIR BAG
13. Reconnect both battery cables, battery negative cable last.
 Nut torque: 8.0 N•m (0.82 kg-m, 71 in-lb)
14. Reset the clock and the radio settings.
15. Perform required additional service.
 Refer to the ESM: ELECTRICAL & POWER CONTROL > POWER SUPPLY,
GROUND & CIRCUIT ELEMENTS > BASIC INSPECTION > INSPECTION AND
ADJUSTMENT > ADDITIONAL SERVICE WHEN REMOVING BATTERY
NEGATIVE TERMINAL > Required Procedure After Battery Disconnection
10. Use the Quick Scan Tool to scan
the QR code (serial number) on
the new driver air bag module.
 The serial number will
automatically populate.
HINT: If needed, the serial number
can be entered manually.
QR code
Serial number
7/7 NTB24-019
PARTS INFORMATION
DESCRIPTION PART NUMBER QUANTITY
MODULE ASSY-AIR BAG 98510-xxxxx (1) 1
(1) Use the EPC and the VIN of the vehicle you are working on to obtain the correct part
number
CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID DESCRIPTION OP CODE FRT
PD103 Replace Driver’s Air Bag Module
Assembly PD1030 0.6
AMENDMENT HISTORY
PUBLISHED DATE REFERENCE DESCRIPTION
February 28, 2024 NTB24-019 Original bulletin published

**************************************************************************************************************

**************************************************************************************************************

SEOCONTENT-END