Classification: AT22-012

Reference: NTB22-085

Date: September 28, 2022

 

VOLUNTARY SAFETY RECALL CAMPAIGN
2020-2022 TITAN/TITAN XD; TCM AND ECM REPROGRAM

CAMPAIGN ID #:	R22B1, R22A9
APPLIED VEHICLES:	2020-2022 Titan and Titan XD (A61)

 

INTRODUCTION

Nissan is conducting this voluntary safety recall campaign, on certain specific model year 2020-2022 Titan and Titan XD vehicles, to reprogram the TCM and ECM. This service will be performed at no charge to the customer for parts or labor.

 

IDENTIFICATION NUMBER

Nissan has assigned identification numbers R22B1 (2WD) and R22A9 (4WD) to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign.

 

DEALER RESPONSIBILITY

It is the dealer’s responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer’s inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale.

Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

 

SERVICE PROCEDURE

 

Confirm the current TCM part number IMPORTANT: Before starting, make sure:

• ASIST on the CONSULT PC has been synchronized (updated) to the current date.
• All C-III plus software updates (if any) have been installed.

NOTICE

• Connect a battery maintainer or smart charger set to reflash mode or a similar setting. If the vehicle battery voltage drops below 12.0V or rises above 15.5V during reprogramming, the TCM or ECM may be damaged.
• Turn the hazard warning lamps ON.

• • Turn OFF all other vehicle electrical loads such as exterior lights, interior lights, HVAC, blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, If any other electrical loads remain ON, the TCM or ECM may be damaged.
• Be sure to connect the AC Adapter.

If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and the TCM or ECM may be damaged.

• Turn OFF all external Bluetooth^® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the VI. If Bluetooth^® signal waves are within range of the CONSULT PC or VI during reprogramming, reprogramming may be interrupted and the TCM or ECM may be damaged.

HINT:

• Take the vehicle for a 10 minute drive in order to meet the following Idle Air Volume Learning conditions:
  • Engine coolant temperature: 70 – 100°C (158 – 212°F)
  • Battery voltage: More than 9 V (At idle)
  • Transmission: Warmed up
• When ECM reprogramming is complete, you will be required to perform Throttle Valve Closed Position, Idle Air Volume Learning, Accelerator Closed Position, and DTC Erase.

 

1. Connect the VI to the vehicle.

 

2. Start C-III plus.

 

3. Wait for the VI to be recognized (Figure 1 on page 3).

• The serial number will display when the VI is recognized.

 

4. Select Re/programming, Configuration.

 

5. Check the box to confirm the precaution instructions have been read, and then select Next.

NOTE: Use the arrows (if needed) to view and read all the precautions.

 

6. Select Automatic Selection(VIN).

 

7. Allow C-III plus to perform automatic VIN selection.

 

8. Confirm the VIN or Chassis # is correct, and then select Confirm.

 

9. Allow the System call to be performed.

 

10. Confirm the VIN is correct for the vehicle, and then select Confirm.

 

11. Select TRANSMISSION.

 

12. Select Reprogramming.

 

13. Find the TCM Part Number and write it on the repair order, and then select Save. NOTE: This is the current Part Number (P/N).

 

14. Compare the Part Number you wrote down in step 13 on page 7 to the numbers in the CURRENT TCM PART NUMBER column in Table A below.

• If there is a match, proceed to step 15 on page 9 to continue the TCM reprogramming procedure.
• If there is not a match, reprogramming is not needed. Skip to CLAIMS INFORMATION on the last page.

NOTE: If TCM reprogramming is not needed, ECM reprogramming is not required.

 

Table A

GRADE	MODEL YEAR	CURRENT TCM PART NUMBER: 31039 –
4WD	2020	9FV3A, 9FV3B, 9FV3D, 9FV3E, 9FV4E, 9FV5C, 9FV7A, 9FV7B, 9FV7D, 9FV7E, 9FW1B, 9FW1C, 9FW2B, 9FW2C
	2021	9FV3D, 9FV3E, 9FV5A, 9FV5B, 9FV7D, 9FV7E 9FV8B, 9FV8C 9FW4A, 9FW4B, 9FW5A, 9FW5B, 9FW7B, 9FW7C, 9FW7E, 9FW8B, 9FW8C, 9FW8E, 9FW9B, 9FW9C
	2022	9FW7C , 9FW7E, 9FW8C, 9FW8E, 9FW9B, 9FW9C
2WD	2020	9FV1A, 9FV1B, 9FV1D, 9FV1E, 9FV4D, 9FW0B, 9FW0C
	2021	9FV1D, 9FV1E, 9FV4B, 9FV4C 9FW3A, 9FW3B, 9FW6B, 9FW6C, 9FW6E, 9FW9A
	2022	9FW6C, 9FW6E, 9FW9A

 

Reprogram the TCM

 

15. Follow the on-screen instructions to navigate C-III plus and reprogram the TCM.

• If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle.

 

16. Select Next, and then proceed to step 17 on page 11.

 

NOTE: When the screen in Figure 12 displays, TCM reprogramming is complete. If the screen in Figure 12 does not display (indicating that reprogramming did not complete), refer to the information on the next page.

 

TCM Recovery: 

Do not disconnect the VI or shut down C-III plus if reprogramming does not complete. 

If reprogramming does not complete and the “!?” icon displays, as shown in Figure 13:

• Check battery voltage (12.0 V – 15.5 V).
• Ignition is ON, engine is OFF.
• External Bluetooth® devices are OFF.
• All electrical loads are OFF.
• Select Retry and follow the on screen instructions.
• Retry may not go through on first attempt and can be selected more than once.

 

If reprogramming does not complete and the “X” icon displays, as shown in Figure 14: 

• Check battery voltage (12.0 V – 15.5 V).
• CONSULT A/C adapter is plugged in.
• Ignition is ON, engine is OFF.
• Transmission is in Park.
• All C-III plus / VI cables are securely connected.
• All C-III plus updates are installed.
• Select Home, and restart the reprogram procedure from the beginning.

 

17. Follow the on-screen instructions to Erase All DTCs.

• When the entire TCM reprogramming process is complete, the screen in Figure 15 will display.

 

18. Verify the before and after part numbers are different.

 

19. Print a copy of this screen (Figure 15) and attach it to the repair order for warranty documentation.

 

20. Select Confirm, and then proceed to step 21 on page 12 to confirm the ECM part number.

 

Confirm the current ECM part number 

21. Return to the home screen and perform steps 4 – 10 on pages 3 – 6.

 

22. Select ENGINE.

 

23. Select Reprogramming.

 

24. Find the ECM Part Number and write it on the repair order, and then select Save. NOTE: This is the current Part Number (P/N).

 

25. Compare the Part Number you wrote down in step 24 to the numbers in the CURRENT ECM PART NUMBER column in Table B below.

• If there is a match, continue to step 26 on page 14 to continue the ECM reprogramming procedure.
• If there is not a match, ECM reprogramming is not needed and the procedure is complete. Skip to CLAIMS INFORMATION on the last page.

 

Table B

GRADE	MODEL YEAR	CURRENT ECM PART NUMBER: 23710 –
4WD	2020	FV93B, FV93C, FV93D, EZ94B, EZ94C, EZ94D 9FV8C, 9FV8D, 9FV8E, 9FV9C, 9FV9D, 9FV9E
	2021	9FW3B, 9FW3C, 9FW3D, 9FW3E 9FW4B, 9FW4C, 9FW4D, 9FW4E 9FW5B, 9FW5C, 9FW5D, 9FW5E 9FW6B, 9FW6C, 9FW6D, 9FW6E
	2022	9GK2C, 9GK2D, 9GK3C, 9GK3D, 9GK4C, 9GK4D 9GK5C, 9GK5D
2WD	2020	EZ91B, EZ91C, EZ91D, EZ92B, EZ92C, EZ92D
	2021	9FW1B, 9FW1C, 9FW1D, 9FW1E 9FW2B, 9FW2C, 9FW2D, 9FW2E
	2022	9GK0C, 9GK0D, 9GK1C, 9GK1D

 

Reprogram the ECM

26. Follow the on-screen instructions to navigate C-III plus and reprogram the ECM.

NOTE: In some cases, more than one new P/N for reprogramming is available.

• If you get this screen and it is blank (no reprogramming listed), it means there is no reprogramming available for this vehicle.

 

27. Select Next, and then proceed to step 28 on page 16.

NOTE: When the screen in Figure 20 displays, ECM reprogramming is complete. If the screen in Figure 20 does not display (indicating that reprogramming did not complete), refer to the information on the next page.

 

ECM Recovery:

Do not disconnect the VI or shut down C-III plus if reprogramming does not complete.

If reprogramming does not complete and the “!?” icon displays as shown in Figure 21: 

• Check battery voltage (12.0 V – 15.5 V).
• Ignition is ON, engine is OFF.
• External Bluetooth® devices are OFF.
• All electrical loads are OFF.
• Select Retry and follow the on screen instructions.
• Retry may not go through on first attempt and can be selected more than once.

 

If reprogramming does not complete and the “X” icon displays as shown in Figure 22: 

• Check battery voltage (12.0 V – 15.5 V).
• CONSULT A/C adapter is plugged in.
• Ignition is ON, engine is OFF.
• Transmission is in Park.
• All C-III plus / VI cables are securely connected.
• All C-III plus updates are installed.
• Select Home, and restart the reprogram procedure from the beginning.

 

28. Follow the on-screen instructions to Erase All DTCs.

• When the entire reprogramming process is complete, the screen in Figure 23 will display.

 

29. Verify the before and after part numbers are different.

 

30. Print a copy of this screen (Figure 23) and attach it to the repair order for warranty documentation.

 

31. Select Confirm.

 

32. Disconnect the battery maintainer/smart charger from the vehicle.

 

33. Perform Throttle Valve Closed Position, Idle Air Volume Learning and Accelerator Closed Position.

 

---

Transmission Control Module (TCM) Reprogram – 2020-2023 Nissan Titan & Frontier

 

Transmission Control Module (TCM) Reprogram – 2020-2023 Nissan Titan & Frontier

 

---

Remedy Instructions and TSB

RCRIT-22V671-4122.pdf 721.503KB

 

---

Latest Recalls Documents

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V671&docType=RCL

 

---

 

Reprogramming

J2534-1 Re/Programming

• J2534-1

• Reprogramming

• Blank Programming

 

---

Tutorial for Purchasing NERS Software

Software updated April 26, 2019 to version # 04.03.00. It is recommended the latest version of NERS be installed before connecting to a vehicle.

This NERS software supports reprogrammable Engine and Transmission control units from 1999 to 2019 model year vehicles, and 2005 MY and later VIN writing into ECUs, when using a Nissan validated pass-through device. Click the Reprogramming Tab for additional information on reprogramming. This software only provides ECU reprogramming, blank programming and VIN writing capability. It does not provide diagnostic or key programming capability. For Engine and Transmission control unit reprogramming and VIN writing capability on 2020 MY & newer, please use CONSULT-III plus or CONSULT-III plus R2R software.

Vehicle reprogramming requires the use of the following:

• Nissan validated J2534-1 device
• Nissan ECU Reprogramming Software (NERS)
• Personal computer running Windows XP (SP2 or later) or Windows 7 or 10 64Bit
• Applicable reprogram file

 

Nissan tested and validated the below listed devices. Nissan does not recommend the use of any other J2534-1 device not listed here.

Manufacturer	Models
Actia	PassThru +XS
Autel	MaxiFlash Elite (with firmware v3.01)
Bosch	Mastertech VCI (SFP v5.11.9)
Dearborn Group	VSI-2534
Drew Technologies/OPUS IVS	CarDAQ Plus, CarDAQ M, Mongoose ISO/CAN
Hella Gutmann Solutions	Mega Macs 42 SE (DT VCI), Mega Macs 66 (DT66)
Texa	TEXA Navigator TXTs Series

Click the below link to purchase NERS diagnostic software.

Purchase NERS Software

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

• Visit the ECU File Downloads Page

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will no longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

 

---

When you purchase a J-2534 reprogramming file, you will get a zip file containing a data file (.dat, .pdx, .xcal, .7z), a .csv or .xml file and a Reprog_readme.pdf. Please review the readme file for information on where to place the files in your PC.

Please Note that J2534-1 supports reprogramming on 1999 MY and later vehicles.

 

How to find the proper J-2534 Reprogramming ECU file:

In order for you to locate the proper ECU file, you will need to look up the applicable Technical Services Bulletin(TSB) for your vehicle. Instructions in the TSB will pinpoint and advise you of the ECU part # to enter below.

•  Search for TSB.

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

• Visit the ECU File Downloads Page

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will not longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

Special Note: Nissan and Infiniti vehicle uses a high level of security when Re/programming or Configuration is performed to the vehicle ECUs. With the release of NERS software version 04.00.01 or greater, technicians will be required to login with their Nissan or Infiniti Techinfo website user ID and password to perform Re/programming and Configuration in NERS.
Login Instruction Guide

 

---

September 2013, Nissan and Infiniti began the phase in of “Blank” Service Parts ECUs and TCMs. Depending upon the model and model year, replacement modules come WITHOUT software. When a replacement module is installed in an applicable vehicle for any reason, it will need to be programmed.

When you purchase a J-2534 Blank programming file, you will get a zip file containing a data file (.dat, .pdx, .xcal, .7z), a .csv or .xml file and a Reprog_readme.pdf. Please review the readme file for information on where to place the files in your PC.

 

How to find the proper J-2534 Blank Programming ECU file:

• Obtain the blank ECU part number when you purchase the replacement ECU. Nissan’s and Infiniti’s parts catalog provides both the blank ECU part number and the ROM-DATA ID part number (after programming part number) to be used. Enter this blank ECU part number in the field below.

or

• Using C-III plus software, retrieve the blank ECU part number from the new ECU. Enter this blank ECU part number in the field below.

Please note: Take care after making your selection that the listed vehicle information matches the vehicle you are programming.

• Special Note: NERS Version 03.08 or higher supports Blank RWD, 5 speed TCM programming.

 

Download Purchased ECU Data File(s)

Once you have purchased ECU data file(s) and your order is completed, your ECU files can be downloaded. Please verify that you are logged in to your account before proceeding.

• Visit the ECU File Downloads Page

Purchase of ECU data enables file download access for a period of 24 hours, after which time the file will not longer appear in your list of purchased data files. Be sure to download all data files immediately following your purchase.

Special Note: Nissan and Infiniti vehicle uses a high level of security when Re/programming or Configuration is performed to the vehicle ECUs. With the release of NERS software version 04.00.01 or greater, technicians will be required to login with their Nissan or Infiniti Techinfo website user ID and password to perform Re/programming and Configuration in NERS.
Login Instruction Guide

 

	Drew Tech CarDAQ-Plus 3 Diagnostic Code Reader and J2534 Programming Tool
	Drew Technologies (DRWCDPLUSKIT) CarDAQ-Plus J2534 Flash Reprogramming Kit
	Drew Tech Mongoose Pro ISO-CAN 2
	VSI J2534 ECU Reprogrammer & Diagnostic Adapter
	BOSCH Automotive Tools MTECH2 Mastertech II J2534
	Autel MaxiFlash Elite VCI J2534 Pass-Thru

 

www.nissan-techinfo.com

 

---

 

 

---

Last update on 2025-04-16 / Affiliate links / Images from Amazon Product Advertising API

---

 

This product presentation was made with AAWP plugin.