2014-2019 Nissan NV200 Taxi Body Builders Guide

SEOCONTENT-START

2014-2019NV200
TAXI
BODY BUILDER’S GUIDE
NISSAN Commercial Vehicles
SHIFT_the way you move
FOREWORD
This manual contains body builder’s information for the
2014-2019 NISSAN NV200 Taxi.
In order to assure your safety and the efficient functioning of
the vehicle, this guide should be read thoroughly.
All information in this guide is based on the latest product
information at the time of publication. The right is reserved
to make changes in specifications and methods at any time
without notice.
IMPORTANT SAFETY NOTICE
The proper performance of procedures is essential for both
the safety of the technician and the efficient functioning of
the vehicle. The methods in this Body Builder’s Guide are
described in such a manner that they may be performed
safely and accurately. Methods vary with the procedures
used, the skills of the technician and the tools and parts
available. Accordingly, anyone using procedures, tools or
parts which are not specifically recommended by Nissan
must first be completely satisfied that neither personal
safety nor the vehicle’s safety will be jeopardized by the
method selected.
WARNINGS, CAUTIONS AND NOTES USED IN THIS MANUAL
WARNING:
This is used to indicate the presence of a hazard that could cause death or serious injury. To
avoid or reduce the risk, the procedures must be followed precisely.
CAUTION:
This is used to indicate the presence of a hazard that could cause minor or moderate
personal injury or damage to your vehicle. To avoid or reduce the risk, the procedures must
be followed carefully.
NOTE:
This is used to provide additional information.
Edition: July 2013
Revision: August 2018
Publication Number: BG19EMM20TU0

4 2014-2019 NV200 TAXI
GENERAL INFORMATION
DISCLAIMER
Important Regulatory Information
Emission standards and motor vehicle safety standards for new vehicles and equipment have been
established by the United States Government under the provisions of the Clean Air Act, the Noise
Control Act, and the National Traffic and Motor Vehicle Safety Act. These Acts govern Nissan as the
original equipment manufacturer of the NISSAN NV200 Taxi vehicles. They also govern dealers, body
builders, and all others who manufacture and market new motor vehicles and equipment. Part 568
of the Title 49 Code of Federal Regulations (CFR) describes requirements for intermediate
manufacturers, final-stage manufacturers, and manufacturers who assume legal responsibility for
a vehicle. This Body Builder’s Guide (Guide) partially fulfills Nissan’s obligations as the original
equipment manufacturer. Additionally, this guide identifies regulatory requirements to assist
intermediate and final stage manufacturers to determine their obligations to conform with these
standards.
Compliance labels affixed to NISSAN NV200 Taxi vehicles indicate the status of initial compliance as
of the date of manufacture by Nissan. Any subsequent modifications made to this vehicle may
affect the final certification of the engine, vehicle or equipment. The body builder, conversion
company, or dealer responsible for any modification has the responsibility to certify that the
modified vehicle and equipment complies or continues to comply with all applicable motor vehicle
safety standards and emissions regulations. The body builder, conversion company, or dealer is
responsible for making sure the modifications or installed equipment do not affect the safety of the
vehicle, including modifications which may result in a collision, property damage, personal injury or
death.
Nissan does not assume responsibility as the final stage manufacturer for modified or altered
vehicles. Nissan is not responsible for final certification, product liability claims, or warranty claims,
resulting from any component, assembly, or system altered by or at the request of the body builder,
conversion company, dealer or vehicle purchaser. Nissan is not responsible for modifications which
cause the vehicle to become noncompliant with any of the motor vehicle safety standards,
emissions regulations, or modifications that cause the vehicle to be or become defective or unsafe.
Disclaimer
All information, specifications and illustrations in this manual are those in effect at the time of
printing. Nissan reserves the right to change specifications or design without notice and without
obligation.
The body builder, conversion company, aftermarket equipment manufacturer, second stage
manufacturer, upfitter, dealer and the vehicle purchaser are responsible to abide by all regulations
issued by the National Highway Traffic Safety Administration (NHTSA), the Occupational Safety and
Health Act (OSHA), state, local, or provincial government laws. These regulations and laws may
require the installation of additional equipment for the intended use of the vehicle.
© 2018 Nissan North America, Inc. All rights reserved. No part of this Body Builder’s Guide may be
reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan
North America, Inc.
DISCLAIMER
SERVICE INFORMATION AND TOOLS
For service information, refer to www.nissan-techinfo.com.
For special service tools, refer to www.nissantechmate.com.
SERVICE INFORMATION AND TOOLS
CONTACT INFORMATION
General
Nissan Commercial and Fleet Aftermarket Engineering 1 (855) 651-6655 or by E-mail at
Nissan-AET@Nissan-USA.COM.
CONTACT INFORMATION
[GENERAL INFORMATION]
2014-2019 NV200 TAXI 7
WARRANTY
Emissions Control SystemWarranty
For Nissan warranty information, refer to the Warranty Information Booklet in the Owner’s Manual
package.
WARRANTY
SAFETY INFORMATION
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) PRECAUTIONS
Precautions for Supplemental Restraint System (SRS) “Air Bag” and “Belt Pre-Tensioner”
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or
death in the event of a collision which could result in air bag inflation, it is recommended
that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system or failure of the system to work
properly in the event of an accident.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or
death in the event of a collision which would result in air bag inflation, the front passenger
seat cannot be permanently removed.
• Do not use electrical test equipment on any circuit related to the SRS. SRS wiring harnesses
can be identified by yellow and/or orange harnesses or harness connectors.
Precautions When Using Power Tools (Air or Electric) and Hammers
WARNING:
• When working near the Air bag Diagnosis Sensor Unit or other Air bag System sensors with
the ignition ON or engine running, DO NOT use air or electric power tools or strike near the
sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air
bag(s), possibly causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF,
disconnect the battery or batteries, and wait at least 3 minutes before performing any
service. Care should be taken to avoid damaging or contacting SRS components. Doing so
may cause the system to improperly operate in the event of a collision.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) PRECAUTIONS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 11
SRS COMPONENT LOCATIONS — 2014-2017 MODEL YEARS
TGAAZIA0029ZZ
SRS COMPONENT LOCATIONS — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
12 2014-2019 NV200 TAXI
1. Driver air bag module 2. Front passenger air bag OFF indicator
3. Front passenger air bag module 4. Spiral cable
5. Seat belt buckle switch LH (RH similar) 6. Air bag diagnosis sensor unit (view with center
console assembly removed)
7. Combination meter (air bag warning lamp) 8. Crash zone sensor (view with front bumper
removed)
9. Front RH seatbelt pre-tensioner (view with RH
pillar removed) (LH similar)
10. Front side air bag satellite sensor RH (view
with RH pillar finisher re-moved) (LH similar)
11. Front LH side air bag module (RH similar) 12. LH side front curtain air bag module (RH similar)
13. Occupant classification control unit 14. Occupant classification system sensors
15. Front door satellite sensor LH (view with front
door finisher LH removed) (RH similar)
16. Side rear curtain air bag module (view with
headliner removed)
17. Rear side air bag satellite sensor LH (view with
lower luggage finish panel removed) (RH similar)
TGAAZIA0030ZZ
SRS COMPONENT LOCATIONS — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 13
OCCUPANT CLASSIFICATION SYSTEM
WARNING:
After removal and installation of the front passenger seat, a zero point reset function must
be performed. It is recommended that this be performed by a NISSAN dealer using a
special tool. If zero point reset is not performed, the occupant classification system may not
operate normally which may increase the risk of serious injury or death in a collision.
WARNING:
Do not disturb or modify the front passenger seat wiring. Failure to follow this instruction
may cause incorrect operation of the occupant classification system and front passenger air
bag or system failure and may increase the risk of serious injury or death in a collision.
The front passenger seat is equipped with seat weight sensors as part of the supplemental
restraints occupant classification system. The occupant classification sensors (weight sensors) are
on the seat cushion frame under the front passenger seat and are designed to detect an occupant
and objects on the seat. The front passenger air bag status lamp is illuminated when the system is
disabled. For occupant classification system and front passenger air bag operation, refer to the
Owner’s Manual. For repair of the front passenger seat, occupant classification system, air bags or if
an air bag warning lamp is illuminated, It is recommended that you visit a NISSAN dealer.
OCCUPANT CLASSIFICATION SYSTEM
[SAFETY INFORMATION]
14 2014-2019 NV200 TAXI
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
FRONT AIR BAG MODULE LOCATIONS
WARNING:
Modifications must not interfere with air bag modules or deployment zones. Damage to air
bag modules may cause serious personal injury or death. Objects placed within air bag
deployment zones may cause serious personal injury or death.
NOTE:
Do not add accessory items that, when installed, will interfere with the installed position of
the air bag or the zones of the deploying air bags.
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 15
: Front of vehicle.
1. Driver air bag module 2. Side curtain air bag module,
driver
3. Side air bag module, driver
4. Side air bag module, passenger
5. Side curtain air bag module,
passenger
6. Front passenger air bag
module
Front Air Bag Modules — Overhead View
= Air Bag Module Locations (No modifications in these areas.)
AAZIA0335GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
16 2014-2019 NV200 TAXI
: Front of vehicle.
1. Side curtain air bag module
(located behind LH side of
headlining and across windshield
header)
2. Side air bag module (located
at outboard side of driver seatback)
3. Driver air bag module
(located in steering wheel)
Front Air Bag Modules — Driver Side
= Air Bag Module Locations (No modifications in these areas.)
AAZIA0349GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 17
: Front of vehicle.
1. Side curtain air bag module
(located behind RH side of
headlining and across windshield
header)
2. Front passenger air bag
module (located in RH side of
instrument panel)
3. Side air bag module (located
at outboard side of passenger
seatback)
Front Air Bag Modules — Passenger Side
= Air Bag Module Locations (No modifications in these areas.)
AAZIA0350GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
18 2014-2019 NV200 TAXI
A. Center of the driver air bag module
housing
B. 267.5mm(10.53 in) C. Maximum lateral projection of
the deployed driver air bag 535
mm(21.06 in)
D. 267.5mm(10.53 in)
Driver Air Bag Deployment Width
= Driver Air Bag Module
AAZIA0343GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 19
A. Maximum lateral projection
of the deployed front
passenger air bag 475mm
(18.7 in)
B. Center of front passenger air
bag module housing
C. 237.5mm(9.35 in)
D. Reference point: glove box
striker inboard fastener
E. 199mm(7.83 in) F. 38.5mm(1.52 in)
Front Passenger Air Bag Deployment Width
= Front Passenger Air Bag Module
AAZIA0344GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
20 2014-2019 NV200 TAXI
AIR BAG DEPLOYMENT KEEP-OUT ZONES
: Front of vehicle.
* Center of seat
1. Reference point: instrument
panel edge
2. Reference point: door glass
trim edge
3. Reference point: seat center
lines
4. Reference point: door glass
trim edge
5. Reference point: instrument
panel seam
A. 735mm(28.94 in)
B. 1,050mm(41.34 in) C. 500mm(19.69 in) D. 1,415mm(55.71 in)
E. 580mm(22.83 in) F. 732.1mm(28.82 in) G. 651mm(25.63 in)
Front Air Bag Keep-Out Zones — Overhead View
Air Bag Deployment Keep-out Zones (No modifications in these areas.)
Air Bag Inflation Zones
AAZIA0354GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 21
: Front of vehicle.
A. 635mm(25 in) B. 510mm(20.08 in) C. 685mm(26.97 in)
D. 405mm(15.94 in) E. 915mm(36.02 in) F. 355mm(13.98 in)
Front Air Bag Keep-Out Zone — Driver Side View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0358GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
22 2014-2019 NV200 TAXI
: Front of vehicle.
1. Reference point: zone follows
windshield surface
2. Reference point: zone follows
instrument panel surface contour
A. 635mm(25.00 in)
B. 405mm(15.94 in) C. 685mm(26.97 in) D. 510mm(20.08 in)
Front Air Bag Keep-Out Zone — Passenger Side View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0359GB
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 23
INFLATED AIR BAG ZONE DIMENSIONS
1. Reference point: door glass
trim edge
2. Maximum inflated driver air
bag
3. Reference point: vehicle center
line
4. Maximum inflated front passenger
air bag
5. Reference point: door glass
trim edge
A. 150mm(5.91 in) between
door glass trim edge and air
bag.
B. 535mm(21.06 in) C. 535mm(21.06 in) D. 475mm(18.70 in)
E. 690mm(27.17 in) F. 150mm(5.91 in) between
door glass trim edge and air
bag.
G. 120mm(4.72 in)
H. 125mm(4.92 in)
Driver and Passenger Air Bag Inflation Zones — Forward View
AAZIA0258ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
24 2014-2019 NV200 TAXI
: Front of vehicle.
1. Maximum inflated driver air
bag
2. Maximum inflated front passenger
air bag
3. Reference point: instrument
panel seam
A. 110mm(4.33 in) between
instrument panel and air bag.
B. 340mm(13.39 in) C. 645mm(25.39 in)
D. 40mm(1.57 in)
Front Air Bag Inflation Zones — Overhead View
AAZIA0259ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 25
: Front of vehicle.
1. Maximum inflated side curtain
air bag
2. Maximum inflated side air
bag
3. Maximum inflated driver air
bag
A. 760mm(29.92 in) B. 750mm(29.53 in) C. 350mm(13.78 in )
D. 550mm(21.65 in) E. 200mm(7.87 in) F. 110mm(4.33 in) between
instrument panel and air bag.
Front Air Bag Inflation Zones — Driver Side View
AAZIA0256ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
26 2014-2019 NV200 TAXI
: Front of vehicle.
1. Maximum inflated side curtain
air bag
2. Front edge of front passenger
air bag module
3. Maximum inflated front passenger
air bag
4. Maximum inflated side air
bag
A. 760mm(29.92 in) B. 750mm(29.53 in)
C. 645mm(25.39 in) D. 550mm(21.65 in) E. 350mm(13.78 in)
Front Air Bag Inflation Zones — Passenger Side View
AAZIA0283ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 27
: Front of vehicle.
A. 210mm(8.27 in) B. 60mm(2.36 in) between
door glass trim edge and air
bag.
C. 60mm(2.36 in) between
door glass trim edge and air
bag.
D. 210mm(8.27 in)
Side Curtain Air Bag Inflation Zones — Overhead View
AAZIA0260ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
28 2014-2019 NV200 TAXI
: Front of vehicle.
A. 200mm(7.87 in) B. 115mm(4.53 in) between
door glass trim edge and air
bag.
C. 115mm(4.53 in) between
door glass trim edge and air
bag.
D. 200mm(7.87 in)
Side Air Bag Inflation Zones — Overhead View
AAZIA0261ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 29
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL
YEARS
WARNING:
Modifications must not interfere with air bag modules or deployment zones. Damage to air
bag modules may cause serious personal injury or death. Objects placed within air bag
deployment zones may cause serious personal injury or death.
NOTE:
Do not add accessory items that, when installed, will interfere with the installed position of
the air bag or the zones of the deploying air bags.
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
30 2014-2019 NV200 TAXI
REAR SIDE CURTAIN AIR BAG DEPLOYMENT KEEP-OUT ZONES
: Front of vehicle.
* Center of seat
1. Reference point: Exterior body
side surface
2. Reference point: seat center
lines
3. Reference point: Exterior
body side surface
4. Reference point: Partition
panel assembly
A. 1,120mm(44.09 in) B. 480mm(18.90 in)
C. 480mm(18.90 in) D. 1,120mm(44.09 in)
Rear Side Curtain Air Bag Keep-Out Zones — Overhead View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0345GB
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 31
: Front of vehicle.
1. Reference point: Forward
edge of interior trim panel
2. Reference point: Partition
finish panel
3. Reference point: Partition
window surface
A. 195mm(7.68 in) B. 595mm(23.43 in) C. 1,025mm(40.35 in)
D. 230mm(9.06 in) E. 540mm(21.26 in) F. 165mm(6.50 in)
G. 705mm(27.76 in) H. 415mm(16.34 in)
Rear Side Curtain Air Bag Keep-Out Zone — Driver Side View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0346GB
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
32 2014-2019 NV200 TAXI
: Front of vehicle.
1. Reference point: Partition
window surface
2. Reference point: Partition
finish panel
3. Reference point: Forward
edge of interior trim panel
A. 165mm(6.50 in) B. 540mm(21.26 in) C. 230mm(9.06 in)
D. 1,025mm(40.35 in) E. 595mm(23.43 in) F. 195mm(7.68 in)
G. 415mm(16.34 in) H. 705mm(27.76 in)
Rear Side Curtain Air Bag Keep-Out Zone — Passenger Side View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0380GB
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 33
INFLATED REAR SIDE CURTAIN AIR BAG ZONE DIMENSIONS
1. Reference point: Exterior body
side surface
2. Maximum inflated rear side
curtain air bag
3. Maximum inflated rear side
curtain air bag
4. Reference point: Exterior
body side surface
A. 155mm(6.10 in) B. 175mm(6.89 in)
C. 175mm(6.89 in) D. 155mm(6.10 in)
Rear Side Curtain Air Bag Inflation Zones — Forward View
AAZIA0475ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
34 2014-2019 NV200 TAXI
: Front of vehicle.
1. Reference point: vehicle
center line
2. Reference point: Exterior
body side surface
3. Maximum inflated rear side
curtain air bag
4. Maximum inflated rear side
curtain air bag
5. Reference point: Exterior
body side surface
A. 155mm(6.10 in)
B. 175mm(6.89 in) C. 175mm(6.89 in) D. 155mm(6.10 in)
Rear Side Curtain Air Bag Inflation Zones — Overhead View
AAZIA0263ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 35
: Front of vehicle.
1. Maximum inflated rear side
curtain air bag
2. Rear side curtain air bag
module
A. 530mm(20.87 in)
B. 965mm(37.99 in)
Rear Side Curtain Air Bag Inflation Zones — Driver Side View
AAZIA0264ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
36 2014-2019 NV200 TAXI
: Front of vehicle.
1. Rear side curtain air bag
module
2. Maximum inflated rear side
curtain air bag
A. 965mm(37.99 in)
B. 530mm(20.87 in)
Rear Side Curtain Air Bag Inflation Zones — Passenger Side View
AAZIA0265ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2014-2017 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 37
SRS COMPONENT LOCATIONS — 2018-2019 MODEL YEARS
TGAAZIA0031ZZ
SRS COMPONENT LOCATIONS — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
38 2014-2019 NV200 TAXI
1. Driver air bag module 2. Front passenger air bag OFF indicator
3. Front passenger air bag module 4. Spiral cable
5. Seat belt buckle switch LH (RH similar) 6. Air bag diagnosis sensor unit (view with center
console assembly removed)
7. Combination meter (air bag warning lamp) 8. Crash zone sensor (view with front bumper
removed)
9. Front RH seatbelt pre-tensioner (view with RH
pillar finisher removed) (LH similar)
10. Front side air bag satellite sensor RH (view
with RH pillar finisher removed) (LH similar)
11. Front LH side air bag module (RH similar) 12. LH side front curtain air bag module (RH similar)
13. Occupant classification control unit 14. Occupant classification system sensors
15. Front door satellite sensor LH (view with front
door finisher LH removed) (RH similar)
16. Side rear curtain air bag module (view with
headliner removed)
17. Rear side air bag satellite sensor LH (view with
lower luggage finish panel removed) (RH similar)
TGAAZIA0030ZZ
SRS COMPONENT LOCATIONS — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 39
OCCUPANT CLASSIFICATION SYSTEM
WARNING:
After removal and installation of the front passenger seat, a zero point reset function must
be performed. It is recommended that this be performed by a NISSAN dealer using a
special tool. If zero point reset is not performed, the occupant classification system may not
operate normally which may increase the risk of serious injury or death in a collision.
WARNING:
Do not disturb or modify the front passenger seat wiring. Failure to follow this instruction
may cause incorrect operation of the occupant classification system and front passenger air
bag or system failure and may increase the risk of serious injury or death in a collision.
The front passenger seat is equipped with seat weight sensors as part of the supplemental
restraints occupant classification system. The occupant classification sensors (weight sensors) are
on the seat cushion frame under the front passenger seat and are designed to detect an occupant
and objects on the seat. The front passenger air bag status lamp is illuminated when the system is
disabled. For occupant classification system and front passenger air bag operation, refer to the
Owner’s Manual. For repair of the front passenger seat, occupant classification system, air bags or if
an air bag warning lamp is illuminated, It is recommended that you visit a NISSAN dealer.
OCCUPANT CLASSIFICATION SYSTEM
[SAFETY INFORMATION]
40 2014-2019 NV200 TAXI
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
AIR BAG MODULE LOCATIONS
WARNING:
Modifications must not interfere with air bag modules or deployment zones. Damage to air
bag modules may cause serious personal injury or death. Objects placed within air bag
deployment zones may cause serious personal injury or death.
NOTE:
Do not add accessory items that, when installed, will interfere with the installed position of
the air bag or the zones of the deploying air bags.
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 41
: Front of vehicle.
1. Driver air bag module 2. Side curtain air bag module,
driver
3. Side air bag module, driver
4. Side air bag module, passenger
5. Side curtain air bag module,
passenger
6. Front passenger air bag
module
Front Air Bag Modules — Overhead View
TGAAZIA0007GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
42 2014-2019 NV200 TAXI
: Front of vehicle.
1. Side curtain air bag module
(located behind LH side of
headlining and across windshield
header)
2. Side air bag module (located
at outboard side of driver seatback)
3. Driver air bag module
(located in steering wheel)
Front Air Bag Modules — Driver Side
TGAAZIA0008GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 43
: Front of vehicle.
1. Side curtain air bag module
(located behind RH side of
headlining and across windshield
header)
2. Front passenger air bag
module (located in RH side of
instrument panel)
3. Side air bag module (located
at outboard side of passenger
seatback)
Front Air Bag Modules — Passenger Side
= Air Bag Module Locations (No modifications in these areas.)
AAZIA0350GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
44 2014-2019 NV200 TAXI
A. Center of the driver air bag module
housing
B. 267.5mm(10.53 in) C. Maximum lateral projection of
the deployed driver air bag 535
mm(21.06 in)
D. 267.5mm(10.53 in)
Driver Air Bag Deployment Width
TGAAZIA0009GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 45
A. Maximum lateral projection
of the deployed front
passenger air bag 475mm(18.7
in)
B. Center of front passenger air
bag module housing
C. 237.5mm(9.35 in)
D. Reference point: glove box
striker inboard fastener
E. 199mm(7.83 in) F. 38.5mm(1.52 in)
Front Passenger Air Bag Deployment Width
= Front Passenger Air Bag Module
AAZIA0344GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
46 2014-2019 NV200 TAXI
AIR BAG DEPLOYMENT KEEP-OUT ZONES
: Front of vehicle.
* Center of seat
1. Reference point: instrument
panel edge
2. Reference point: door glass
trim edge
3. Reference point: seat center
lines
4. Reference point: door glass
trim edge
5. Reference point: instrument
panel seam
A. 735mm(28.94 in)
B. 1,050mm(41.34 in) C. 500mm(19.69 in) D. 1,415mm(55.71 in)
E. 580mm(22.83 in) F. 732.1mm(28.82 in) G. 651mm(25.63 in)
Front Air Bag Keep-Out Zones — Overhead View
Air Bag Deployment Keep-out Zones (No modifications in these areas.)
Air Bag Inflation Zones
AAZIA0354GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 47
: Front of vehicle.
A. 635mm(25 in) B. 510mm(20.08 in) C. 685mm(26.97 in)
D. 405mm(15.94 in) E. 915mm(36.02 in) F. 355mm(13.98 in)
Front Air Bag Keep-Out Zone — Driver Side View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0358GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
48 2014-2019 NV200 TAXI
: Front of vehicle.
1. Reference point: zone follows
windshield surface
2. Reference point: zone follows
instrument panel surface contour
A. 635mm(25.00 in)
B. 405mm(15.94 in) C. 685mm(26.97 in) D. 510mm(20.08 in)
Front Air Bag Keep-Out Zone — Passenger Side View
= Air Bag Inflation Zone
= Air Bag Deployment Keep-out Zone (No modifications in this area.)
AAZIA0359GB
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 49
INFLATED AIR BAG ZONE DIMENSIONS
1. Reference point: door glass
trim edge
2. Maximum inflated driver air
bag
3. Reference point: vehicle center
line
4. Maximum inflated front passenger
air bag
5. Reference point: door glass
trim edge
A. 150mm(5.91 in) between
door glass trim edge and air
bag.
B. 607mm(23.89 in) C. 607mm(23.89 in) D. 475mm(18.70 in)
E. 690mm(27.17 in) F. 150mm(5.91 in) between
door glass trim edge and air
bag.
G. 120mm(4.72 in)
H. 125mm(4.92 in)
Driver and Passenger Air Bag Inflation Zones — Forward View
AAZIA0258ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
50 2014-2019 NV200 TAXI
: Front of vehicle.
1. Maximum inflated driver air
bag
2. Maximum inflated front passenger
air bag
3. Reference point: instrument
panel seam
A. 110mm(4.33 in) between
instrument panel and air bag.
B. 393mm(15.47 in) C. 645mm(25.39 in)
D. 40mm(1.57 in)
Front Air Bag Inflation Zones — Overhead View
AAZIA0259ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 51
: Front of vehicle.
1. Maximum inflated side curtain
air bag
2. Maximum inflated side air
bag
3. Maximum inflated driver air
bag
A. 760mm(29.92 in) B. 750mm(29.53 in) C. 350mm(13.78 in )
D. 550mm(21.65 in) E. 284mm(11.18 in) F. 110mm(4.33 in) between
instrument panel and air bag.
Front Air Bag Inflation Zones — Driver Side View
AAZIA0256ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
52 2014-2019 NV200 TAXI
: Front of vehicle.
1. Maximum inflated side curtain
air bag
2. Front edge of front passenger
air bag module
3. Maximum inflated front passenger
air bag
4. Maximum inflated side air
bag
A. 760mm(29.92 in) B. 750mm(29.53 in)
C. 645mm(25.39 in) D. 550mm(21.65 in) E. 350mm(13.78 in)
Front Air Bag Inflation Zones — Passenger Side View
AAZIA0283ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 53
: Front of vehicle.
A. 210mm(8.27 in) B. 60mm(2.36 in) between
door glass trim edge and air
bag.
C. 60mm(2.36 in) between
door glass trim edge and air
bag.
D. 210mm(8.27 in)
Side Curtain Air Bag Inflation Zones — Overhead View
TGAAZIA0007ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
54 2014-2019 NV200 TAXI
: Front of vehicle.
A. 200mm(7.87 in) B. 115mm(4.53 in) between
door glass trim edge and air
bag.
C. 115mm(4.53 in) between
door glass trim edge and air
bag.
D. 200mm(7.87 in)
Side Air Bag Inflation Zones — Overhead View
AAZIA0261ZZ
FRONT AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 55
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL
YEARS
WARNING:
Modifications must not interfere with air bag modules or deployment zones. Damage to air
bag modules may cause serious personal injury or death. Objects placed within air bag
deployment zones may cause serious personal injury or death.
NOTE:
Do not add accessory items that, when installed, will interfere with the installed position of
the air bag or the zones of the deploying air bags.
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
56 2014-2019 NV200 TAXI
REAR SIDE CURTAIN AIR BAG DEPLOYMENT KEEP-OUT ZONES
: Front of vehicle.
* Center of seat
1. Reference point: Exterior body
side surface
2. Reference point: seat center
lines
3. Reference point: Exterior
body side surface
4. Reference point: Partition
panel assembly
A. 1,627mm(64.05 in) B. 480mm(18.90 in)
C. 480mm(18.90 in) D. 1,627mm(64.05 in)
Rear Side Curtain Air Bag Keep-Out Zones — Overhead View
TGAAZIA0010GB
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 57
: Front of vehicle.
1. Reference point: Forward
edge of interior trim panel
2. Reference point: Partition
window surface
3. Reference point: Partition
finish panel
A. 104.91mm(4.13 in) B. 775.65mm(30.54 in) C. 836.65mm(32.93 in)
D. 66.13mm(2.60 in) E. 573mm(22.56 in) F. 532.6mm(20.96 in)
G. 1,379.54mm(54.31 in) H. 166.63mm(6.56 in)
Rear Side Curtain Air Bag Keep-Out Zone — Driver Side View
TGAAZIA0011GB
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
58 2014-2019 NV200 TAXI
: Front of vehicle.
1. Reference point: Partition
window surface
2. Reference point: Forward
edge of interior trim panel
3. Reference point: Partition
finish panel
A. 66.13mm(2.60 in) B. 836.65mm(32.93 in) C. 775.65mm(30.54 in)
D. 104.91mm(4.13 in) E. 532.6mm(20.96 in) F. 573mm(22.56 in)
G. 166.63mm(6.56 in) H. 1,379.54mm(54.31 in)
Rear Side Curtain Air Bag Keep-Out Zone — Passenger Side View
TGAAZIA0012GB
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 59
INFLATED REAR SIDE CURTAIN AIR BAG ZONE DIMENSIONS
1. Reference point: Exterior body
side surface
2. Maximum inflated rear side
curtain air bag
3. Maximum inflated rear side
curtain air bag
4. Reference point: Exterior
body side surface
A. 179.5mm(7.07 in) B. 406mm(15.98 in)
C. 406mm(15.98 in) D. 179.5mm(7.07 in)
Rear Side Curtain Air Bag Inflation Zones — Forward View
TGAAZIA0009ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
60 2014-2019 NV200 TAXI
: Front of vehicle.
1. Reference point: vehicle
center line
2. Reference point: Exterior
body side surface
3. Maximum inflated rear side
curtain air bag
4. Maximum inflated rear side
curtain air bag
5. Reference point: Exterior
body side surface
A. 179.5mm(7.07 in)
B. 406mm(15.98 in) C. 406mm(15.98 in) D. 179.5mm(7.07 in)
Rear Side Curtain Air Bag Inflation Zones — Overhead View
TGAAZIA0010ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 61
: Front of vehicle.
1. Maximum inflated rear side
curtain air bag
2. Rear side curtain air bag
module
A. 600mm(23.62 in)
B. 1,627mm(64.05 in)
Rear Side Curtain Air Bag Inflation Zones — Driver Side View
TGAAZIA0011ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
62 2014-2019 NV200 TAXI
: Front of vehicle.
1. Rear side curtain air bag
module
2. Maximum inflated rear side
curtain air bag
A. 600mm(23.62 in)
B. 1,627mm(64.05 in)
Rear Side Curtain Air Bag Inflation Zones — Passenger Side View
TGAAZIA0012ZZ
REAR SIDE CURTAIN AIR BAG DEPLOYMENT ZONES — 2018-2019 MODEL YEARS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 63
ALTERED VEHICLES
Safety / Emissions
Certification Labels for Altered Vehicles
A person or company who alters a previously certified vehicle before the first purchase by the final
customer in such a manner that its stated weight ratings are revised, is required by Federal
Regulation (49 CFR Part 567.7) to affix an Altered Vehicle Certification Label in addition to the FMVSS
Certification Label. The label must be affixed to the vehicle in the manner and form described in 49
CFR Part 567.4:
• The label shall, unless riveted, be permanently affixed in such a manner that it cannot be removed without
destroying or defacing it.
• The label shall be affixed to either the hinge pillar, B-pillar, or the door edge that meets the door-latch post
next to the driver’s seating position or, if none of these locations is practicable, to the left side of the
instrument panel (other permissible locations are also specified in 49 CFR Part 567.4).
• The lettering on the label shall be of a color that contrasts with the background of the label.
• The label shall contain the required statements in the English language and lettered in block capitals and
numerals not less than three thirty-seconds of an inch high.
• The lettering shall be permanent. If typed or written, a protective clear cover may be necessary to prevent
information from being wiped off.
• Label must not cover or obscure the FMVSS Certification Label.
The label must meet the following requirements as described in Section 9:
• Shall be permanently attached.
• Shall be affixed adjacent to the original compliance label required by Section 6.
• The lettering of the label shall be clear, indelible, indented, or embossed, or of a color that contrasts with the
background color of the label, and in block capitals and numerals not less than 2.0mm(0.1 in) high.
• The label shall be permanently affixed to the same surface as that to which the FMVSS label is affixed.
NOTE:
The National Highway Traffic Safety Administration (NHTSA) requires that any automobile
dealer that installs accessories on a vehicle prior to first retail sale must install a special label
(“reduced capacity label”) on that vehicle if the total weight of all accessories on that vehicle
exceed 1.5 percent of the vehicle’s gross vehicle weight rating (GVWR) or 100 lbs., whichever is
less. This includes accessories that the dealer puts on (OE and after market), AND accessories
installed at the VPC.
If the yellow label is applied near the tire and loading information on the driver’s side B pillar,
load carrying capacity shown on the yellow label supersedes previous load information.
ALTERED VEHICLES
[SAFETY INFORMATION]
64 2014-2019 NV200 TAXI
BRAKE COMPLIANCE GUIDELINES
Brake Compliance Guidelines (FMVSS)
Any changes to the vehicle must still comply with FMVSS allowing for the following provisions:
• No alterations, modifications or replacements are made to the following systems:
• parking brake
• anti-lock brakes
• engine vacuum
• steering
• wheels or tires
• brakes
• indicator lamps and wiring
• brake system reservoir labeling
• suspension ride height or spring rate
• The vehicle is re-balanced by the addition of an equivalent weight if components are permanently
removed.
• The applicable GAWRs and GVWR weights are not exceeded.
• The vertical distance from the ground to the completed vehicle center of gravity should not
exceed 703mm(27.7 in) at the Gross Vehicle Weight Rating (GVWR).
BRAKE COMPLIANCE GUIDELINES
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 65
FMVSS REGULATION LIST
Standards
For FMVSS standards, refer to the following website:
https://www.nhtsa.gov/staticfiles/rulemaking/pdf/FMVSS-QuickRefGuide-HS811439.pdf
FMVSS REGULATION LIST
[SAFETY INFORMATION]
66 2014-2019 NV200 TAXI
PRECAUTIONS
Precautions For Electrical CAN (Controller Area Network) System
• Do not modify the CAN system.
• For additional information and identification of CAN system, refer to the Service Manual or
contact Nissan Commercial and Fleet Aftermarket Engineering 1 (855) 651-6655 or by E-mail at
Nissan-AET@Nissan-USA.COM.
PRECAUTIONS
[SAFETY INFORMATION]
2014-2019 NV200 TAXI 67
MODEL INFORMATION
LABEL INFORMATION
Identification Number
1. SRS air bag warning label 2. Air conditioning specification
label
3. Transmission fluid
specification label
4. Brake fluid warning label
(Canada Only)
5. Emission control information
label
6. Tire and loading information
label
7. Vehicle identification number
(Chassis number) (located near
right side of passenger seat)
8. FMVSS Certification Label 9. Vehicle identification number
(VIN) plate
10. SRS air bag warning label
AAZIA0284ZZ
LABEL INFORMATION
[MODEL INFORMATION]
68 2014-2019 NV200 TAXI
VEHICLE CODING INFORMATION
Vehicle Identification
Vehicle Identification Number Arrangement
Position Character Qualifier Definition
1
3N8 Manufacturer
3N8: Mexico produced
Nissan MPV
4 C Engine type C: MR20DE
M0 Vehicle line M0: Model Code M20
7 J Body type J: Taxi
8 T Restraint system
T: 2+3 Seating Capacity,
2WD, Class C
1st Row: Driver and
Passenger 3-Point
Manual Belts, Frontal Air
Bags, Side Air Bags and
Curtain Side Air Bags
2nd Row Outboard:
3-Point Manual Belts and
Curtain Side Air Bags
2nd Row Center: 3-Point
Manual Belt
9 * Check digit
(0 to 9 or X) The code for
the check digit is
determined by a
mathematical
computation.
10
E
Model year
E: 2014
F F: 2015
G G: 2016
H H: 2017
J J: 2018
K K: 2019
11 K Manufacturing plant
K: CIVAC (Cuernavaca,
Mexico)
XXXXXX Vehicle serial number Chassis number
VEHICLE CODING INFORMATION
[MODEL INFORMATION]
2014-2019 NV200 TAXI 69
CLASS
Model Variation
Prefix and suffix designations:
Position Character Qualifier Definition
1 T Body type T: MPV
DR Engine DR: MR20DE (2.0L)
4 A Axle A: 2WD
5 L Drive L: LH
6 D Grade D: S
7 V Transmission V: CVT
9 M20 Model M20: NV200 Taxi
10
11 E Intake E: EGI
12 U Zone U: USA
13 T Equipment T: Taxi Equipment
XXXXX Option Codes Option Codes
Body Engine Transmission Destination Grade Equipment Model
Taxi
MR20DE
(2.0L)
CVT USA S NV200 Taxi TDRALDV-EUT
CLASS
[MODEL INFORMATION]
70 2014-2019 NV200 TAXI
GVWR CAPACITY
Gross Vehicle Weight Rating (GVWR) is the weight specified by Nissan as the maximum allowable
weight for the loaded vehicle.
The GVW must not exceed the Gross Vehicle Weight Rating (GVWR) shown on the FMVSS
Certification Label. The GVW equals the combined weight of the unloaded vehicle, passengers,
luggage and any other optional equipment. In addition, front or rear GAW must not exceed the
Gross Axle Weight Rating (GAWR) shown on the FMVSS Certification Label.
GVWR CAPACITY
[MODEL INFORMATION]
2014-2019 NV200 TAXI 71
DIMENSIONS
Resource Chart
Item Grade ! TAXI
Base CurbWeight – Total kg (lbs) 1,645 (3,627)
2014-2017 Model Years: Base Curb
Weight – Rear
kg (lbs)
706 (1,557)
2018-2019 Model Years: Base Curb
Weight – Rear
706 (1,556)
Base CurbWeight – Front kg (lbs) 939 (2,070)
2014 Model Year: Maximum GVWR –
Max. Pass., Plus Cargo
kg (lbs)
2,140 (4,718)
2015-2019 Model Years: Maximum
GVWR – Max. Pass., Plus Cargo
2,205 (4,861)
Max. Tires and Load Rating @ 290 kPa
(42 psi) – Rear
kg (lbs)
185/65R15
92T XL
480 (1,058)
Max. Tires and Load Rating @ 290 kPa
(42 psi) – Front
kg (lbs)
185/65R15
92T XL
480 (1,058)
2014 Model Year: Maximum Payload
kg (lbs)
495 (1,091)
2015-2019 Model Years: Maximum
Payload
560 (1,235)
2014 Model Year: Rear GAWR
kg (lbs)
1,140 (2,513)
2015-2019 Model Years: Rear GAWR 1,145 (2,524)
2014-2017 Model Years: Front GAWR
kg (lbs)
1,060 (2,338)
2018-2019 Model Years: Front GAWR 1,060 (2,337)
Maximum Cargo Width at WheelWells mm(in) 1,188.2 (46.8)
Maximum Cargo Width at Floor mm(in) 1,192.5 (46.9)
Maximum Cargo Height mm(in) 1,309 (51.5)
Maximum Cargo Length at Floor –
Behind Seat
mm(in) 726.6 (28.6)
Maximum Cargo Length- Behind Seat
Back in Upright Position
mm(in) 544 (21.4)
Cargo Volume m3 (ft 3) 1.031 (36.4)
Vehicle Height Without Roof Lamp
mm(in) ! 1,872.7 (73.7)
With Roof Lamp
mm(in) ! 1,893.3 (74.5)
Wheelbase mm(in) 2,925 (115.2)
Wheel Type — Steel
Front Tread Width mm(in) 1,525 (60)
Rear Tread Width mm(in) 1,520 (59.8)
Turning Radius m(ft) 11.2 (36.7)
Cargo Area Liftover Height mm(in) 537.2 (21.1)
DIMENSIONS
[MODEL INFORMATION]
72 2014-2019 NV200 TAXI
Item Grade ! TAXI
Slide Door Opening Width – Maximum
Clearance, Without Door
Without Door Seal and
Interior Trim
mm(in) ! 819.5 (32.3)
With Door Seal and
Interior Trim
mm(in) ! 812.8 (32)
Slide Door Opening Width – Maximum
Clearance, With Door
Without Door Seal and
Interior Trim
mm(in) ! 673.7 (26.5)
With Door Seal and
Interior Trim
mm(in) ! 670.4 (26.4)
Slide Door Opening Height – Maximum
Clearance
Without Door Seal and
Interior Trim
mm(in) ! 1,184.1 (46.6)
With Door Seal and
Interior Trim
mm(in) ! 1,155.5 (45.5)
Vehicle Length Without License Bracket
mm(in) ! 4,732.5 (186.3)
With License Bracket
mm(in) ! 4,746.9 (186.9)
Front Overhang Without License Bracket
mm(in) ! 961.3 (37.8)
With License Bracket
mm(in) ! 975.8 (38.4)
Rear Overhang mm(in) 845.7 (33.3)
Rear Door Opening Height – Maximum
Clearance
mm(in) 1,231.2 (48.5)
Rear Door Opening Width – Maximum
Clearance
mm(in) 1,222.7 (48.1)
Vehicle Width – With Mirrors mm(in) 2,010.1 (79.1)
Vehicle Width – With Mirrors Folded mm(in) 1,852.8 (72.9)
Vehicle Width – With Mirrors Folded and
Auto Steps Retracted (2014–2017
Model Years)
mm(in) 1,834.3 (72.2)
Vehicle Width – With Mirrors Folded and
Fixed-type Side Step
mm(in) 1,895.5 (74.6)
Vehicle Width – With Slide Doors Open mm(in) 1,990.1 (78.35)
Ground Clearance – With Vehicle
Parked
mm(in) 146.3 (5.8)
Ground Clearance – With Vehicle
Running
mm(in) 140.5 (5.5)
Step-in Height – Front mm(in) 376.8 (14.8)
Step-in Height – From Slide Door
Opening
mm(in) 487.6 (19.2)
DIMENSIONS
[MODEL INFORMATION]
2014-2019 NV200 TAXI 73
Item Grade ! TAXI
Step-in Height – From Entry Step (Auto
Step)
mm(in) 263.9 (10.4)
Step-in Height – From Entry Step (Fixed
Step)
mm(in) 237 (9.33)
Step-in Height – Rear mm(in) 537.2 (21.2)
DIMENSIONS
[MODEL INFORMATION]
74 2014-2019 NV200 TAXI
ELECTRICAL
SELF-TEST MODE
This vehicle is capable of performing a function test of various systems on the vehicle.
To enter the Self-Test Mode
1. Close the hood and front door RH, and lift the wiper arms from the windshield (to prevent windshield
damage due to wiper operation).
NOTE:
When this test mode is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch more than 20 times.
Then turn the ignition switch OFF.
4. Turn the ingition switch ON within 10 seconds. After that the auto active test starts.
5. After a series of the following operations is repeated 3 times, auto active test is complete.
When the vehicle in this Self-Test Mode the following devices on the vehicle will momentarily
operate in the order shown to verify that the systems are functioning correctly.
• RR Defogger
• Front wipers (HI, LO)
• Parking lamp
• License plate lamp
• Tail lamp
• Headlamp (LO, HI)
• A/C compressor (magnetic clutch)
• Cooling fan
After the self-test has been completed (3 on/off cycles) the vehicle will be returned to normal
operating mode. If the operator wishes to terminate the test early they may do so by turning the
ignition switch OFF.
SELF-TEST MODE
[ELECTRICAL]
2014-2019 NV200 TAXI 75
DATA LINK CONNECTOR LOCATION (FOR DIAGNOSTIC SCAN TOOL)
Consult Checking System
2014 model year vehicles are equipped with a data link
connector located behind the fuse panel cover on the lower left
side of the instrument panel.
1. Data Link Connector
Vehicles built from 2015 model year to present are equipped
with a data link connector located underneath the instrument
panel below the steering column.
1. Data Link Connector
The vehicle is diagnosed using the CONSULT-III plus.
• When CONSULT is connected with a data link connector equipped on the vehicle side, it will communicate
with the control unit equipped in the vehicle and then enable various kinds of diagnostic tests.
• Refer to “CONSULT-III plus Operation Manual” for more information.
TGAAZIA0001ZZ
TGAAZIA0015ZZ
DATA LINK CONNECTOR LOCATION (FOR DIAGNOSTIC SCAN TOOL)
[ELECTRICAL]
76 2014-2019 NV200 TAXI
SHIPPING (EXTENDED STORAGE) MODE CONTROL SYSTEMS
Determining Shipping (Extended Storage) Mode Status
1. Turn ignition switch ON.
2. Check that extended storage warning message is not displayed in instrument cluster or display after 20
seconds.
If the extended storage warning message is displayed in instrument cluster or display refer to
Canceling Extended Storage (pg. 78).
SHIPPING (EXTENDED STORAGE) MODE CONTROL SYSTEMS
[ELECTRICAL]
2014-2019 NV200 TAXI 77
SHIPPING MODE (EXTENDED) STORAGE SYSTEM CANCEL
Canceling Extended Storage
1. Turn ignition switch OFF.
2. Press in (turn off) the extended storage switch. Refer to Extended Storage Switch (pg. 78).
NOTE:
Pressing in the switch moves the mode from shipping to normal.
Extended Storage Switch
The following switch is mounted on the fuse block (Junction Box) for transportation and storage.
The fuse block (Junction Box) is located in the glove box, refer to Fuse and Relay Information (pg. 86)
Remove the extended storage switch if it causes interference when checking fuses, refer to How to
remove the Extended Storage Switch (pg. 79).
How to turn the Extended Storage Switch ON/OFF
CAUTION:
• Turn the ignition switch OFF when operating the extended storage switch.
• Under normal conditions, keep the extended storage switch in ON state. Never operate the
extended storage switch except when necessary.
1
AAZIA0595ZZ
1. Extended storage switch
SHIPPING MODE (EXTENDED) STORAGE SYSTEM CANCEL
[ELECTRICAL]
78 2014-2019 NV200 TAXI
• To turn the extended storage switch ON, pull it up in direction A as shown in the figure.
• To turn the extended storage switch OFF, press it in direction B as shown in the figure.
How to remove the Extended Storage Switch
1. Turn the ignition switch OFF.
2. Turn the extended storage switch OFF.
3. Pinch tabs A and and firmly pull out the extended storage switch in B direction to remove the extended
storage switch.
CAUTION:
For bus bar type extended storage switch, never replace bus bar with a fuse, or fuse may
continually open.
AAZIA0596ZZ
AAZIA0597ZZ
SHIPPING MODE (EXTENDED) STORAGE SYSTEM CANCEL
[ELECTRICAL]
2014-2019 NV200 TAXI 79
NOTE:
• Extended storage switch and fuse (or bus bar) are removed together. Remove fuse (or bus
bar) from extended storage switch, if necessary.
• Install removed fuse (or bus bar) to fuse block.
• Extended storage switch is for transportation and storage. Reinstallation of switch is not
required after removal, but fuse (or bus bar) must be reinstalled/pushed back in to
activate all electrical systems and turn message off (which may be shown in meter/display).
SHIPPING MODE (EXTENDED) STORAGE SYSTEM CANCEL
[ELECTRICAL]
80 2014-2019 NV200 TAXI
BCM TRANSIT MODE (2014–2015 MODEL YEARS)
Description
Systems that are affected by BCM Transit mode are the Lock/Unlock/Panic via Remote Keyless
Entry (remote key fob, when applicable), the Interior Illumination and the Head Lights. These
systems will not operate while the ignition is OFF, but will operate with it ON
Determining BCM Transit Mode Status
To determine if the BCM Transit Mode is still active turn the ignition to ON. If the vehicle is still in BCM
Transit Mode, the hazard lights in the instrument cluster will illuminate for 1 minute .
Canceling BCM Transit Mode Status
1. Turn the ignition OFF.
2. Do the following at the same time for 2 seconds:
• Move wiper switch to the high position (all the way down), and
• Move turn signal switch to the left position (all the way down).
3. To confirm Transit Mode is OFF:
• Move the turn signal switch to the center (neutral) position.
• Turn the ignition ON – the turn signal indicators should stay OFF (not illuminate).
NOTE:
Some important facts to remember:
• BCM Transit Mode can only be canceled.
• You cannot switch back to BCM Transit Mode once it has been canceled.
• BCM Transit Mode should not be canceled until just prior to customer delivery.
BCM TRANSIT MODE (2014–2015 MODEL YEARS)
[ELECTRICAL]
2014-2019 NV200 TAXI 81
FUSE AND RELAY INFORMATION
Fuses and Relays — Engine Compartment
WARNING:
Tampering with or modifying the electrical system may cause safety equipment malfunction
possibly resulting in serious injury or death.
CAUTION:
This information is reference only. To avoid damage, modification of the vehicle’s electrical
systems is not recommended. For pre-wiring access points, refer to CUSTOMER PRE-WIRING
ACCESS (pg. 92).
: Front of vehicle.
TGAAZIA0026ZZ
FUSE AND RELAY INFORMATION
[ELECTRICAL]
82 2014-2019 NV200 TAXI
Item Fuse/relay color Fuse rating
Power supply
condition
Fuse/relay name
1 Yellow 20A Battery
Rear window
defogger
2 — — — Not used
3 Yellow 20A Battery ECM relay
4 — — — Not used
5 Green 30A Battery Front wiper
6 Red 10A Battery
Parking, license
plate and tail
lamps
7 — — — Not used
8 — — — Not used
9 Red 10A Battery A/C clutch
10 Blue 15A Battery Front fog lamp
11 Red 10A Ignition
Headlamp (high
RH)
12 Red 10A Ignition
Headlamp (high
LH)
13 Blue 15A Ignition
Headlamp (low
LH)
14 Blue 15A Ignition
Headlamp (low
RH)
15 Red 10A Ignition, Start
A/T control
system
16 Red 10A Ignition, Start REV lamp IGN
17 Red 10A Ignition, Start ABS control
18 — — — Not used
19 — — — Not used
20 Blue 15A Ignition, Start Fuel pump
21 Blue 15A Ignition, Start O 2 sensor
22 Blue 15A Ignition, Start Fuel injector
23 — — — Not used
24 Blue 15A Battery
Throttle control
motor
25 Black — — Ignition relay
26 Black — —
Rear window
defogger relay
27 Black — —
Cooling fan
relay – 2
28 Black — —
Cooling fan
relay – 1
FUSE AND RELAY INFORMATION
[ELECTRICAL]
2014-2019 NV200 TAXI 83
: Front of vehicle.
Item Fuse/relay color Fuse rating
Power supply
condition
Fuse/relay name
1 Red 10A — Taxi Electrical
2 Red 10A Battery
Daytime light
relay 1
3 Red 10A Battery Charging system
4 Red 10A Battery Horn relay
5 Yellow 60A Battery
Electronically
controlled power
steering control
unit
6 — — — Not used
7 Yellow 30A Battery ABS solenoid
8 Blue 40A Battery
BCM power
window relay
9 Blue 40A Battery ABS motor
10 Green 40A Battery Starting system
11 Green 40A Battery
Engine cooling
fan system
12 Green 40A Battery
Engine cooling
fan system
TGAAZIA0027ZZ
FUSE AND RELAY INFORMATION
[ELECTRICAL]
84 2014-2019 NV200 TAXI
Item Fuse/relay color Fuse rating
Power supply
condition
Fuse/relay name
13 Blue 15A Battery Audio
14 Red 10A Battery CVT system
15 Blue 15A — RR Blower
16 Blue 15A — RR Blower
17 Black — — Horn relay
18 — — — Not used
19 Blue — —
Daytime light
relay 2
Taxi Service
20 Black — —
Daytime light
relay 1
Air conditioning
valve
(Deleted as a
production
change during
2016 model year.)
21 Blue — —
Engine cooling
fan system (HI)
22 Blue — —
Engine cooling
fan system (LO)
23 — 80A Battery
Air conditioning,
mirror, power
socket and body
systems
24 — 60A Battery
Ignition, power
train,
transmission and
body systems
25 — 80A Battery
Lighting, body,
charging systems
26 — 100A Battery
BCM, engine
cooling, starting,
transmission
control and audio
systems
27 — 140A Battery Alternator
FUSE AND RELAY INFORMATION
[ELECTRICAL]
2014-2019 NV200 TAXI 85
Fuses and Relays — Interior
Item Fuse/Relay Color Fuse Rating
Power Supply
Condition
Fuse/Relay
Name
1 Blue 15A Ignition
Air conditioning
system
2 Blue 15A Ignition
Air conditioning
system
3 Red 10A Ignition
Air conditioning
system
4 Yellow 20A
Accessory,
Ignition
Front 12V power
socket
5 Yellow 20A
Accessory,
Ignition
Rear 12V power
socket
6 — — — Not used
7 Yellow 20A — Taxi Equipment
8 — — — Not used
9 — — — Not used
10 Red 10A B+
Meter, key switch,
CONSULT
11 Red 10A B+ Stop lamp system
12 Yellow 20A — Taxi Equipment
13 Red 10A B+ BCM
14 — — — Not used
WASHER
MOTOR
AUDIO
/ MIRROR
HEATER
MIRROR
1 . USE SPECI F IED FUSES ONLY
2 . CONTACT A DEALER FOR SYSTEMS NOT L ISTED.
20A
20A
FR POWER
OUTLET
20A
TAXI
SERVICE2
RR POWER
OUTLET
ELEC IG
AIR BAG
METER
10A
ELEC
PARTS1
10A
10A
STOP
LAMP
ELEC
PARTS2
C:1 2 3 4 5/01 3LNOA
15A
10A
BLOWER
20A
TAXI
SERVICE1
BLOWER
AIR COND
UP
AAZIA0267ZZ
FUSE AND RELAY INFORMATION
[ELECTRICAL]
86 2014-2019 NV200 TAXI
Item Fuse/Relay Color Fuse Rating
Power Supply
Condition
Fuse/Relay
Name
15 Red 10A Ignition Ignition system
16 Red 10A Ignition Air bag system
17 Red 10A Ignition
Meter, Bluetooth®
control unit, IT
master, stop
lamp, EPS,
CONSULT system
18 Red 10A Ignition
Wiper and washer
system switch
19 Red 10A
Accessory,
Ignition
BCM, Bluetooth®
control unit, audio,
mirror and
telematics
system
20 Red 10A
Accessory,
Ignition
Heater mirror
21 Blue — Ignition Blower relay
22 Blue — Accessory Accessory relay
23 Black — — Taxi meter relay
24 Blue — — Rear blower relay
25 Blue — Ignition Taxi service relay
FUSE AND RELAY INFORMATION
[ELECTRICAL]
2014-2019 NV200 TAXI 87
GROUNDS
Grounds
CAUTION:
• Do not ground accessories directly to the battery negative terminal on any Nissan vehicle.
Doing so may interfere with the power generation voltage variable control system and
cause poor or inoperative battery charging. Refer to BATTERY VOLTAGE CONTROL
SYSTEM (pg. 90) in this section.
• Install electrical accessories using suitable body ground connections or ground to the
engine block area.
It is the responsibility of the vehicle upfitter to install any grounds necessary for equipment from
aftermarket or second stage equipment manufacturers. Nissan factory grounds should not be
altered.
Permissible Ground Locations
Primary Location — Taxi Service Connector
Use Pins 5 and 7 in the taxi service connector for ground. Be sure to keep circuit load within
specified maximum amperage. Refer to Connector Terminal Layout in CUSTOMER PRE-WIRING
ACCESS (pg. 92).
GROUNDS
[ELECTRICAL]
88 2014-2019 NV200 TAXI
Secondary Location — Underhood
: Front of vehicle.
1. Permissible ground location.
Use a bolt, nut and washers or self-tapping screw with dielectric grease to fasten additional
underhood accessory grounds.
1
AAZIA0207ZZ
GROUNDS
[ELECTRICAL]
2014-2019 NV200 TAXI 89
BATTERY VOLTAGE CONTROL SYSTEM
CAUTION:
• Do not ground accessories directly to the battery negative terminal on any Nissan vehicle.
Doing so may interfere with the power generation voltage variable control system and
cause poor or inoperative battery charging.
• Install electrical accessories using suitable body ground connections or ground to the
engine block area.
• Use electrical accessories with the engine running to avoid discharging the vehicle battery.
Adding electrical devices puts more load on the electrical system and the battery. The engine
control module (ECM) monitors battery voltage. If battery voltage drops below 12 volts, engine RPM
is increased up to 900 RPM (maximum for idle condition when the engine is at normal operating
temperature). RPM will decrease as battery voltage increases. Engine RPM changes are
gradually ramped up and down by ECM control.
For information on ground connections, refer to GROUNDS (pg. 88) in this section.
BATTERY VOLTAGE CONTROL SYSTEM
[ELECTRICAL]
90 2014-2019 NV200 TAXI
BATTERY VOLTAGE CONNECTION
CAUTION:
To avoid vehicle damage, any aftermarket wiring installations must not interfere with OEM
wiring or electrical systems. It is the upfitter’s responsibility to take the following
precautionary measures when any aftermarket electrical wiring is being installed:
• The upfitter is responsible to calculate all additional current load specifications and install
appropriately rated wiring and fuse protection.
• The upfitter is responsible to not exceed the vehicle’s maximum rated current capacity.
• The upfitter is responsible to maintain integrity of the vehicle’s electrical systems.
• The upfitter is responsible for safety testing of any electrical modifications to the vehicle.
Refer to manufacturer specifications for aftermarket electrical accessories to be installed before
making any voltage connections and protect vehicle electrical systems by installing appropriate
fusing devices.
For information on ground connections, refer to GROUNDS (pg. 88) in this section.
BATTERY VOLTAGE CONNECTION
[ELECTRICAL]
2014-2019 NV200 TAXI 91
CUSTOMER PRE-WIRING ACCESS
Connector Terminal Layout
AAZIA0348GB
CUSTOMER PRE-WIRING ACCESS
[ELECTRICAL]
92 2014-2019 NV200 TAXI
T-PEP Harness Routing Conduit
NOTE:
For T-PEP equipment mounting, refer to T-PEP EQUIPMENT (pg. 99).
All conduit openings are 30mm(1.18 in) ID.
1. Conduit opening at instrument
panel behind AV control
unit
2. Conduit opening below instrument
panel at front of center console
3. Conduit opening at front of
center console
4. Conduit opening at partition
behind PIM mounting
area
5. Conduit opening at partition
behind front passenger seat
6. Conduit opening at floor
behind center console
AAZIA0353ZZ
CUSTOMER PRE-WIRING ACCESS
[ELECTRICAL]
2014-2019 NV200 TAXI 93
AV Control Unit and Finish Panel — Exploded View
1. AV control unit 2. Screw, Phillips head (4) 3. AV control unit finish panel
4. Recirculation control button
AAZIA0305ZZ
CUSTOMER PRE-WIRING ACCESS
[ELECTRICAL]
94 2014-2019 NV200 TAXI
AV Control Unit Removal and Installation
Removal
CAUTION:
Use care not to scratch or damage plastic trim parts during removal. Use a plastic trim tool or
wrap a cloth or shop towel around tools when separating finish panels and releasing
retainers.
CAUTION:
Remove battery terminal and AV control unit after a lapse of 30 seconds or more after
turning the ignition switch OFF.
NOTE:
After the ignition switch is turned OFF, the AV control unit continues operating for
approximately 30 seconds. Therefore, data corruption may occur if battery voltage is cut off
within 30 seconds.
NOTE:
For parts locations and fasteners, refer to the AV Control Unit and Finish Panel — Exploded
View (pg. 94).
1. Disconnect the negative battery terminal (1). : Front of
vehicle.
2. Pull and remove the recirculation control button from the
front air control.
AAZIA0278ZZ
AAZIA0302ZZ
CUSTOMER PRE-WIRING ACCESS
[ELECTRICAL]
2014-2019 NV200 TAXI 95
3. Insert a plastic trim tool (1) behind the upper LH and RH
corners of the AV control unit finish panel (2) and gently
pry to release the upper retainer clips. Pull to release
the lower retainer clips and remove the AV control unit
finish panel (2) from the instrument panel.
: Metal clip
: Plastic retainer
4. Remove the 4 Phillips head screws (A) from the AV control
unit (1) mounting brackets.
5. Lift and pull out the AV control unit to access the wiring harness and connectors.
6. Depress the release tabs, disconnect the 6 electrical harness connectors from the AV control
unit and remove.
NOTE:
Arrows in illustration indicate electrical connector release tab locations.
Installation
1. To install, reverse the removal procedure steps.
AAZIA0279ZZ
AAZIA0281ZZ
AAZIA0301ZZ
CUSTOMER PRE-WIRING ACCESS
[ELECTRICAL]
96 2014-2019 NV200 TAXI
ADDING LIGHTS OR DEVICES
Added Lights or Accessories Controlled By Added Switches
This section describes the connection points for added electrical accessories when these
accessories are to be controlled by added switches not a part of the Nissan released vehicle. The
added switches and wiring must have sufficient electrical capacity for the accessory load and must
be protected by appropriate fuses or circuit breakers. Also, added current draw must not cause
total loads to exceed capabilities of the base vehicle wiring.
Electrical Wiring — Adding Lights or Electrical Devices
CAUTION:
Improper electrical tie-ins may affect vehicle operation (i.e., engine, transmission). After all
electrical or vehicle modifications, confirm that no Diagnostic Trouble Codes (DTCs) are
present and all systems operate normally. Road test the vehicle to verify that no DTCs are
present. If DTCs are generated, perform the appropriate diagnostic procedures and repairs.
Vehicle operation (engine/transmission) maybe affected if DTCs are not serviced.
Disconnect the battery negative (ground) cable prior to any vehicle modification. Upon completion
of body or equipment installation, all wiring should be checked for proper routing, etc. to preclude
electrical shorts upon reconnecting the battery negative cable.
Connect only to the upfitter connections identified in the “customer pre-wiring access” section of
this manual. Connecting to any component or wires other than those identified may adversely
affect other systems and their operation.
Radio Frequency Interference (RFI)
During modifications to the vehicle, manufacturers, service technicians, owners and users should
take the necessary precautions to maintain the RFI integrity of components. (United States has RFI
regulations in effect.) Precautionary procedures and components listed below are examples and do
not necessarily represent a complete list.
1. All components required to suppress RFI emissions, which are removed during service, repair, or
modification to the vehicle, must be reinstalled in the manner in which they were installed by
Nissan.
2. Do not modify or change any RF device in a manner not expressly approved by Nissan.
3. Shields on ignition components must remain installed.
4. Replacement of ignition components which are not OEM is not recommended by Nissan.
5. Electrical grounds on all components must be retained.
6. Metallic components installed on the body or chassis must be grounded to the chassis.
7. Electrical circuits added to the vehicle should not be installed near the ignition components.
8. Only “static conductive” accessory drive belts should be used.
9. Drive belts should be of the OEM type or equivalent that will not build up a static electrical
charge.
10. Additional measures may be needed to adequately suppress RFI emissions.
ADDING LIGHTS OR DEVICES
[ELECTRICAL]
2014-2019 NV200 TAXI 97
REGULATIONS FOR ADDING COMMUNICATION EQUIPMENT
FCC Regulations
The FCC rules and regulations are compiled in Title 47 of the Code of Federal Regulations (CFR). They
are initially published in the Federal Register. After October 1 of each year, the GPO compiles all the
changes, additions, and deletions to the FCC rules and publishes an updated CFR. Refer to the
FCC website for the most up-to-date information. The rules are provided in text version and in
portable document format (PDF) and can be viewed using the Adobe Acrobat Reader. The FCC does
not maintain a database of its rules nor does it print or stock copies of the rules and regulations.
To order a copy of Title 47 of the Code of Federal Regulations visit:
https://www.fcc.gov/encyclopedia/rules-regulations-title-47
FCC Notice:
These devices must comply with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. The device may not cause harmful interference.
2. The device must accept any interference received, including interference that may cause
undesired operation.
NOTE:
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
REGULATIONS FOR ADDING COMMUNICATION EQUIPMENT
[ELECTRICAL]
98 2014-2019 NV200 TAXI
T-PEP EQUIPMENT
NOTE:
For pre-wiring electrical connection and harness routing, refer to CUSTOMER PRE-WIRING
ACCESS (pg. 92).
NOTE:
The AV control unit must be removed to access the taxi service wiring connector. Refer to AV Control
Unit Removal and Installation (pg. 95).
TAXI METER MOUNTING
NOTE:
Use appropriate type and size fasteners to avoid interference with any existing components
or wiring.
TAXI METER MOUNTING
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 99
1. Screw, Phillips head (2) 2. AV control unit finish panel 3. Guide tab (3)
4. Storage tray
Taxi Meter Mounting — Exploded View
AAZIA0303ZZ
TAXI METER MOUNTING
[T-PEP EQUIPMENT]
100 2014-2019 NV200 TAXI
Taxi Meter Mounting — Finish Panels Removal and Installation
Removal
CAUTION:
Use care not to scratch or damage plastic trim parts during removal. Use a plastic trim tool or
wrap a cloth or shop towel around tools when separating finish panels and releasing
retainers.
1. Pull and remove the recirculation control button from the
front air control.
2. Insert a plastic trim tool (1) behind the upper LH and RH
corners of the AV control unit finish panel (2) and gently
pry to release the upper retainer clips. Pull to release
the lower retainer clips and remove the AV control unit
finish panel (2) from the instrument panel.
: Metal clip
: Plastic retainer
3. Remove the 2 Phillips head screws (1).
4. Pull upward to release the 2 front retainer clips (3) and lift
out the storage tray (2), releasing the rear guide tabs (4).
Installation
1. To install, reverse the removal procedure steps.
AAZIA0302ZZ
AAZIA0279ZZ
AAZIA0306ZZ
TAXI METER MOUNTING
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 101
Taxi Meter Mounting Dimensions
1. Wire harness access opening
[25mmx 67mm(0.98 in x 2.63 in)]
2. Storage tray outer edge 3. Reinforcement center lines
4. Storage tray outer edge A. 30mm(1.18 in) B. 172.9mm(6.81 in) Taxi meter
mounting area
C. 147.7mm(5.81 in) D. 29.8mm(1.17 in)
NOTE:
For taxi meter attachment, use M6 bolts and nuts with washers (12mm minimum diameter).
AAZIA0268ZZ
TAXI METER MOUNTING
[T-PEP EQUIPMENT]
102 2014-2019 NV200 TAXI
DRIVER INFORMATION MODULE (DIM) MOUNTING
NOTE:
Use appropriate type and size fasteners (such as M5 screws) to avoid interference with any existing
components or wiring.
1. : DIM mounting area
2. : Cutting area for DIM Bracket
A. 114mm(4.49 in) B. 40mm(1.57 in) C. 11mm(0.43 in)
D. 53mm(2.09 in) E. 30mm(1.18 in) F. 22mm(0.87 in)
G. 16mm(0.63 in) H. 7mm(0. 28 in)
Removal
CAUTION:
Use care not to scratch or damage plastic trim parts during removal. Use a plastic trim tool or
wrap a cloth or shop towel around toolswhen separating finish panels and releasing
retainers.
DIM Dimensions
AAZIA0272ZZ
DRIVER INFORMATION MODULE (DIM) MOUNTING
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 103
1. Pull and remove the recirculation control button from the
front air control.
2. Insert a plastic trim tool (1) behind the upper LH and RH
corners of the AV control unit finish panel (2) and gently
pry to release the upper retainer clips. Pull to release
the lower retainer clips and remove the AV control unit
finish panel (2) from the instrument panel.
: Metal clip
: Plastic retainer
3. Insert a plastic trim tool (1) behind the upper LH and RH
corners of the shift selector finish panel (2) and gently pry
to release the upper retainer clips. Pull to release the
lower retainer clips and position the panel aside.
: Plastic retainer
4. Insert a plastic trim tool (1) behind the upper LH and RH
corners of the lower center finish panel (2) and gently pry
to release the upper retainer clips. Pull to release the lower
retainer clips and remove.
: Plastic retainer
Installation
1. To install, reverse the removal procedure steps.
AAZIA0302ZZ
AAZIA0279ZZ
AAZIA0280ZZ
AAZIA0304ZZ
DRIVER INFORMATION MODULE (DIM) MOUNTING
[T-PEP EQUIPMENT]
104 2014-2019 NV200 TAXI
T-PEP PARTITION FINISH PANEL
Exploded View
1. License holder 2. T-PEP Partition assembly 3. Rear upper instrument panel
assembly
4. Bolt (8) 5. Mask (3) 6. License finish panel
7. Rear finish panel 8. Tray assembly 9. Front finish panel
AAZIA0476ZZ
T-PEP PARTITION FINISH PANEL
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 105
Removal
CAUTION:
Use care not to scratch or damage plastic trim parts during removal. Use a plastic trim tool or
wrap a cloth or shop towel around tools when separating finish panels and releasing
retainers.
1. Lift out and remove the license holder from the partition.
2. Remove the front finish panel and tray assembly using the following steps:
a. Disengage all the two piece plastic retainers using a Phillips style screwdriver and rotating the
center portion 1/4 turn.
b. Insert the plastic trim tool behind the tray assembly and release the plastic retainers.
c. Insert the plastic trim tool underneath the top center of the tray assembly and release the metal
clips.
d. Disconnect the electrical connector and remove the front finish panel and tray assembly together.
: Metal clips
: Plastic retainers
AAZIA0477ZZ
T-PEP PARTITION FINISH PANEL
[T-PEP EQUIPMENT]
106 2014-2019 NV200 TAXI
3. Remove the license finish panel using the following steps:
a. Insert a plastic trim tool behind the license finish panel and
release all the metal clips.
b. Disconnect the electrical connectors.
: Metal clips
4. Remove the 2 bolts and rear finish panel.
5. Remove the rear upper instrument panel assembly using the following steps:
a. Insert a suitable small plastic trim tool behind the 3 masks, pry to release and remove the 3 masks
for access to the 3 bolts. Remove the 3 bolts.
b. Remove the bolt behind the license finish panel mounting area.
c. Remove the 2 bolts behind the rear finish panel mounting area.
AAZIA0318ZZ
AAZIA0317ZZ
T-PEP PARTITION FINISH PANEL
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 107
: Metal clips
: Plastic retainers
Installation
1. To install, reverse the removal procedure steps.
AAZIA0320ZZ
T-PEP PARTITION FINISH PANEL
[T-PEP EQUIPMENT]
108 2014-2019 NV200 TAXI
PASSENGER INFORMATION MODULE (PIM) MOUNTING
NOTE:
Partition finish panel must be removed for PIM installation. Refer to T-PEP Partition Finish
Panel (pg. 105).
Mounting point loading not to exceed 13 kg (29 lbs) per weld nut. Total loading across all 3 mounting
points not to exceed 40 kg (88 lbs).
1. PIM Mounting weld nut, upper
M6 x 1.0
2. PIM Display opening area 3. PIM Mounting screws, lower
M6 x 1.0 (2)
A. 190mm(12.6 in) B. 300mm(11.81 in) C. 80mm(3.15 in)
PIM Mounting Dimensions View
AAZIA0478ZZ
PASSENGER INFORMATION MODULE (PIM) MOUNTING
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 109
1. PIM Mounting screws, lower M6 x 1.0 (2) 2. Trim clip holes (2)
Insert a torx bit driver through the trim clip holes, as shown. Loosen the 2 lower PIM mounting
screws to fit slotted PIM mounting brackets and retighten (screw removal is not necessary).
PIM Fastener Locations View
AAZIA0315ZZ
PASSENGER INFORMATION MODULE (PIM) MOUNTING
[T-PEP EQUIPMENT]
110 2014-2019 NV200 TAXI
CREDIT CARD READER MOUNTING
NOTE:
Use appropriate type and size fasteners to avoid interference with any existing components
or wiring.
NOTE:
The upfitter must modify the partition finish panel for credit card reader installation.
Remove the partition finish panel prior to cutting the credit card reader opening. Refer
to T-PEP Partition Finish Panel (pg. 105).
WARNING:
Avoid installation of aftermarket equipment with sharp edges. Edges should have radius
greater than or equal to 3.2mm(0.13 in). Installation of aftermarket equipment with sharp
edges may result in serious personal injury or death in the event of a collision or emergency
braking.
1. Credit card reader mounting area A. 111.6mm(4.59 in) B. 127.4mm(5.02 in)
C. 10mm(0.39 in) from bottom edge of
vent
AAZIA0479ZZ
CREDIT CARD READER MOUNTING
[T-PEP EQUIPMENT]
2014-2019 NV200 TAXI 111
ROOF LIGHT UPPER HOUSING
Removal
1. Remove the 8 screws (A).
2. Separate the upper housing (B) from the roof light
assembly (C) and remove.
Installation
1. To install, reverse the removal procedure steps.
AAZIA0350ZZ
ROOF LIGHT UPPER HOUSING
[T-PEP EQUIPMENT]

SEOCONTENT-END